Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
User's Guide
P2 CAL
P3 Cnt
P4 A2n
P5 GrA
P6 CAP
9. APPENDIX
9.1. ERROR CODES
During the initial power-on testing or during operation it is possible the scale may show an error message. The meaning
of the error messages is described below.
If an error message is shown repeat the procedure that caused the message, turning the balance on, calibration or other
functions. If the error message still is shown then contact your dealer for further support.
ERROR CODE
28
Normal calibrate
After enter cal mode, the display will show UnLoAd. Remove all weight from the pan and wait for
stable.
After stable, balance will show LoAd, put calibrate weight on the pan, here is the useable weight
list.
300g:
30/40/50/60/70/80/90/100/110/120/130/140/150/160/170/180/190/200/210/220/230/240/250/
260/270/280/290/300
600g:
60/80/100/120/140/160/180/200/220/240/260/280/300/320/340/360/380/400/420/440/460/480
/500/520/540/560/580/600
1500g:
150/200/250/300/350/400/450/500/550/600/650//700/750/800/850/900/950/1000/1050/1100/1
150/1200/1250/1300/1350/1400/1450/1500
3000g:
300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800/1900/2000/21
00/2200/2300/2400/2500/2600/2700/2800/2900/3000
after stable, dosplay will show pass, calbrate complete.
No need press any jey during calibrate.
This display will show xxxxxx for indicating the internal counts, you can press
This option is used to select the auto zero maintain.
Options: OFF, 0.5d, 1d, 2d, 4d, Use
pe.
This is used to adjust gravity, when move to another place with big latitude change, you can use this
function to adjust.
After press
key to enter this function, you can use
(use
and
key move active digits, use
sure.
Latitude rate= local latitude/the latitude of the calibrate place.
For example, local latitude is 9.85, the latitude of the calibrate place is 9.75, by this way, the read-
ing data will be bigger than standard, you need input 1.01025, then reading will be correct.
Note: after you do calibrate, this rate will reset to 1.00000.
Set capacity, press
key to select: 300g/600g/1500g/3000g/6000g, for high resolution model, you
can select 150g/200g/1500g/2000g, after you select, press
Err 3
Calibrate weight error
Err 4
Initial Zero is greater than allowed (4% of
maximum capacity) when power is turned
on or when the
Err 6
A/D count is not correct when turning the
scale on
Err 7
Percentage setting error
key to shift, press
key increase value), after input, press
DESCRIPTION
key is pressed.
key to escape.
key to sure, press
,
,
key to key in the latitude rate
to confirm.
POSSIBLES CAUSES
Use incorrect calibrate weight
Weight on the pan when turning the scale
on.
Excessive weight on the pan when zeroing
the scale.
Improper calibration of the scale.
Damaged load cell.
Damaged electronics.
Platform not installed.
Load cell damaged.
Electronics damaged.
0.01% weight must>0.5d
BAR model
key to esca-
key to
Publicidad
Tabla de contenido
