Important Safety Instructions For Battery Charger - Metabo HPT M 18DYA Manual De Instrucciones

11. Keep hands away from rotating parts.
12. Do not perform any operation using your hands
to support or guide the workpiece.
13. Always use with the depth guide securely
attached to the tool and positioned fl at and fi rmly
against the workpiece.
14. Make sure the bit is not contacting the workpiece
before the switch is turned on.
15. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
16. Be careful of the bit rotating direction and the
feed direction.
17. Do not leave the tool running. Operate the tool
only when hand-held.
18. Always switch off and wait for the bit to come to
a complete stop before removing the tool from
workpiece.
19. Do not touch the bit and shaft, collet nut, collet
immediately after operation: it may be extremely
hot and could burn your skin.
20. After changing the bits or making any
adjustments, make sure the collet nut and any
other adjustment devices are securely tightened.
Loose adjustment device can unexpectedly shift,
causing loss of control, loose rotating components
will be violently thrown.
21. Do not use this tool for drilling.
22. Always wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.
23. Defi nitions for symbols used on this tool
V ..............volts
--- ............direct current
n
.............no load speed
0
---/min ...... revolutions or reciprocation per minute
24. Because the cordless power tool operates by battery
power, be aware of the fact that it can begin to operate
at any time.
25. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
26. Keep the tool's terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
27. Use bits of the correct shank diameter suitable for the
speed of the tool.
28. When operating the tool, do not wear work gloves as
such cloth wear can get caught in the tool.
29. Always use the tool and battery at temperatures
between 23°F (-5°C) and 104°F (40°C).
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YFSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable batteries. Other type of batteries may
burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fi re, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fi re and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specifi ed in Table 1.
English
5