General Aspects - Stiga MP 900 Li 48 Manual De Instrucciones

WARNING!: READ THE INSTRUCTION BOOKLET THOROUGHLY
EN
BEFORE USING THE MACHINE. Keep for future reference.
TABLE OF CONTENTS

1. GENERAL ASPECTS ................................... 1

2. SAFETY REGULATIONS .............................. 2
3. GETTING TO KNOW THE MACHINE ........... 6
3.1 Description of the machine and planned
use ........................................................ 6
3.2 Safety signs .......................................... 7
3.3 Identification label ................................. 7
3.4 Main components ................................. 7
4. ASSEMBLY ................................................... 8
4.1 Assembly components .......................... 8
4.2 Assembly of the guide bar and toothed
chain ..................................................... 8
4.3 Extension of the Pruner ........................ 9
5. CONTROLS.................................................. 9
5.1 Throttle control lever .............................. 9
5.2 Throttle locking lever ............................. 9
5.3 Cutting SPEED
6. USING THE MACHINE ................................. 9
6.1 Preliminary operations .......................... 9
6.2 Safety checks ...................................... 10
6.3 Start-up ............................................... 11
6.4 Working ............................................... 11
6.5 Advice for operation ............................ 12
6.6 Stop .................................................... 12
6.7 After use .............................................. 12
7. ROUTINE MAINTENANCE ........................ 13
7.1 General information ............................. 13
7.2 Battery ................................................ 13
7.3 Topping up the chain oil tank ............... 14
7.4 Cleaning .............................................. 14
7.5 chain catcher....................................... 14
7.6 Machine and bar lubrication holes ...... 14
7.7 Nuts and bolts ..................................... 14
8. OCCASIONAL MAINTENANCE ................. 14
8.1 Chain drive sprocket ........................... 14
8.2 Maintenance of the toothed chain ....... 14
8.3 Guide bar maintenance ....................... 15
9. STORING ................................................... 15
9.1 Storing the machine ............................ 15
9.2 Storing the battery ............................... 15
10. HANDLING AND TRANSPORTATION ....... 15
11. ASSISTANCE AND REPAIRS ..................... 16
12. WARRANTY COVERAGE .......................... 16
13. MAINTENANCE TABLE .............................. 16
14. TROUBLESHOOTING ................................ 17
15. ATTACHMENTS ON REQUEST ................. 19
15.1 Battery ................................................ 19
15.2 Battery charger ................................... 19
15.3 Bars and chains .................................. 19
15.4 Battery backpack ................................ 19
adjustment button ........ 9
1. GENERAL ASPECTS
1.1 HOW TO READ THE MANUAL
Some paragraphs in the manual contain
important information regarding safety and
operation and are emphasized in this manner:
DANGER
Failure to observe the warning can
lead to possible personal and/or third
party injury and/or damage.
ATTENTION
Provides details or further information
on what has been previously indicated
and aims to prevent damage to the
machine or cause other damage.
NOTE
Provides additional information unrelated to
dangerous or potentially damaging situations.
The paragraphs inside a grey dotted frame
refer to optional features not available on all
the models referred to in this booklet. Check
if the feature is available on your model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2 REFERENCES
1.2.1 Figures
The figures in these instructions for use are
numbered 1, 2, 3, etc.
The components indicated in the figures are
identified with letters A, B, C, and so on.
Reference to component C in figure 2 is indicated
with the wording: "See Fig. 2.C" or simply "(Fig.
2.C)".
The figures are given as a guide only. The actual
pieces can differ from those illustrated in this
document.
EN - 1