Assembly; Assembly Components; Assembly Of The Guide Bar And Toothed Chain - Stiga MP 900 Li 48 Manual De Instrucciones

Toothed chain: cutting element, consisting
I.
of drive links fitted with small blades called
"teeth" and side connections held in place by
rivets.
J. Chain restraint element: safety
that prevents uncontrolled movements of the
toothed chain should it break or slacken.
K. Bar cover guard: chainsaw cover on the
guide bar to be fitted during handling,
transportation or storage of the machine.
L. Battery: (if non provided with the machine,
see chap. 15 1 "accessories upon request")
device that supplies electric current to the
tool; its specifications and regulations for use
are described in a specific manual.
M. Battery charger (accessory available upon
request, par. 15.2): device used to recharge
the battery; its specifications and directions
for use are described in a specific manual.
Three battery chargers are available: M1
(fast battery charge); M2 (standard battery
charge); M3 (dual battery charge).
N. Connection cable: cable used to connect
the machine to the battery pack.

4. ASSEMBLY

DANGER
The safety regulations to follow are described
in chap. 2. Strictly comply with these
instructions to avoid serious risks or dangers.
For storage and transport purposes, some
components of the machine may not be installed
in the factory and have to be assembled after
unpacking. Follow the instructions below.
ATTENTION
Unpacking and completing the assembly should
be done on a flat and stable surface, with enough
space for machine handling and its packaging,
always making use of suitable equipment. Do not
use the machine until all the instructions provided
in the "ASSEMBLY" section have been carried out.

4.1 ASSEMBLY COMPONENTS

The packaging includes assembly components.
4.1.1 Unpacking
1. Carefully open the packaging, paying attention
not to lose components.
2. Consult the documentation in the box,
including these instructions.
3. Remove all the unassembled parts from the
box.
4. Remove the machine from the box.
5. Dispose of the box and packaging in
device compliance with local regulations.
4.1.2 Fitting the battery backpack
The battery backpack is delivered already
assembled
the strap support (Fig. 2) and carried by hand.
To release the battery backpack, press on the two
upper buttons (Fig. 2.A).
The battery compartments are located on both
sides of the backpack (Fig. 3).
The following can be found on the right side of the
backpack:
• cable socket (Fig. 4.A)
• battery selector (Fig. 4.B)
• one USB port for charging other devices (e.g.
mobile phones) (Fig. 4.C)
To avoid any loose cables, there are grooves on
both sides and at the rear, in which the power
cable can be inserted.
4.2 ASSEMBLY OF THE GUIDE BAR AND
TOOTHED CHAIN
DANGER
Perform all operations with the motor off.
and disconnected from the battery backpack
(Fig. 13).
DANGER
Always wear heavy duty gloves when handling
the bar and chain. Mount the bar and chain
very carefully so as not to impair the safety and
efficiency of the machine. If in doubt, contact your
dealer.
1. Remove the nut (Fig. 5.A) with the supplied
wrench and remove the chain guard (Fig.
5.B) to access the drive pinion and bar seat.
2. Mount the bar (Fig. 6.A) by inserting the stud
bolt (Fig. 6.B) in the groove (Fig. 6.C) and
push it towards the back of the machine body.
3. Mount the chain around the drive pinion
(Fig 7.A) and along the bar guide, being
careful to follow the sliding direction (Fig. 7.B).
If the tip of the bar is equipped with a nose
sprocket, make sure the drive links are
correctly inserted in the sprocket rims (Fig. 8).
EN - 8
(Fig. 1.G) and can be released from
Direction in which
the chain runs