Power Stroke PS80979B Manual Del Operador página 16

WARNING:
NEVER remove nozzles without first turning off the
engine, relieving the water pressure in the trigger
handle, and locking the lock out on the trigger handle.
NEVER point the nozzle at your face or at others. The
quick-connect feature contains small springs that could
eject the nozzle with some force. Failure to follow these
instructions could result in an eye injury or other serious
personal injury.
To connect a nozzle to the spray wand:
 Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
 Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
 Pull back the quick-connect collar.
 Push the nozzle into place in the spray wand.
 Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
 Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
 Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
 Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the top of the machine.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high
pressure hose prior to and during each use and do
not allow it to become kinked. The high pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
To prevent damage to the outer covering:
 Inspect the hose before every use.
 Fully unwrap and straighten hose before use.
 Do not allow the high pressure hose to be kinked.
 Keep hose away from hot surfaces and sharp edges.
 Do not pull unit by high pressure hose.
 Do not allow hose to be crushed or wrapped around
objects.
All manuals and user guides at all-guides.com
OPERATION
WASHING WITH DETERGENT
See Figure 14.
As sold, this unit is designed for use with "downstream"
pressure washer detergents. To convert for use with
"upstream" detergents, contact customer service or a
qualified service center for more information.
 Remove the cap from the soap tank and pour pressure
NOTE: The machine setting of this unit is 1:20, which
 Install the blue soap nozzle on the spray wand.
 Squeeze the trigger and wait approximately 5 seconds
 Spray the detergent on a dry surface using long, even,
NOTE: To use a soap bottle, open the soap container cap.
Remove the filter from the end of the soap injection hose
then slide the hose out of the cap. Place the filter back on
the hose and place the hose in the bottom of the soap bottle.
For detergent application:
With the blue soap nozzle installed on the spray wand and
the engine turned off, submerge the hose and filter down
into the detergent container as far as it will go.
Before shutting off the engine:
 Place the soap injection hose in a bucket of clean water.
 Flush for 1 - 2 minutes (spray clear water through the
 Shut off the engine.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
Page 12 — English
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
washer detergent in the tank. Replace cap on tank.
usually allows the use of 1 gallon detergent without further
dilution. Check your detergent instructions to be sure
additional dilution is not necessary.
for the detergent to appear.
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
spray wand).