Wall Mounting; Installing And Removing The Battery Pack - Porter Cable PCCF920 Manual De Instrucciones

English

Wall Mounting

Some PORTER-CABLE chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Speed Selector (Fig. A)
Your tool is equipped with a speed selector
you to select one of two speeds. Select the speed based on
the application and control the speed of the tool using the
variable speed trigger switch
SPEED 1
Normal Impacting
SPEED 2
High Speed Impacting
Your impact tool can generate the following maximum
torque values (Speed 1 and Speed 2).
nOTE: Output torque is dependent on the speed selected,
with the highest provided in Speed 2.
TOOl sPEED
SPEED 1
PCCF920
SPEED 2
Anvil (Fig. A, F)

WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessory prior to use to ensure that
it contains no cracks.

CAUTION: Inspect anvils, and hog rings prior to
use. Missing or damaged items should be replaced
before use.
1. Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
2. To install an accessory on the anvil, firmly push accessory
onto the anvil 5 .
nOTE: The hog ring
9
to slide on. After the accessory is installed, the hog ring
applies pressure to help provide accessory retention.
3. To remove an accessory, grasp the accessory and firmly
pull it off.
8
3 which allows
1 .
0–900 rpm
0–1900 rpm
Output Torque
100 Ft. Lbs. / 130 Nm
275 Ft. Lbs. / 372 Nm
compresses to allow the accessory
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

Installing and Removing the Battery Pack

(Fig. D)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 7 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. A, E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 8 .
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
of the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side
of the tool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of the tool.
The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.
Variable Speed Trigger Switch (Fig. A)
1. To turn the tool on, squeeze the trigger switch
2. To turn the tool off, release the trigger switch.
3. Your tool is equipped with a brake. The anvil will stop
when the trigger switch is fully released.
4. The variable speed switch enables you to select the best
speed for a particular application. The more you squeeze
the trigger, the faster the tool will operate.
nOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
6 into the tool handle, align the
2 determines the direction
1 .