Product Description And Specifications - Bosch PSM 200 AES Manual Original

Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding and polishing of
wood, plastic, metal, filler and varnished surfaces. It is par-
ticularly well-suited for profiles, corners and hard-to-reach
areas.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Orbital stroke rate preselection thumbwheel
(2) On/off switch
(3) Filter element (Microfilter system)
(4) Dust box, complete (microfilter system)
(5) Ventilation openings
(6) SDS slider for sanding plate release
(7) Front sanding plate
(8) Rear sanding plate
(9) Rectangular sanding plate
(10) Handle (insulated gripping surface)
(11) Extraction outlet
a)
(12) Extraction hose
a)
(13) Dust extraction adapter
a)
(14) Sanding sheet
(15) Louvre sanding attachment
(16) Sanding sheet for sanding finger
a)
(17) Sanding finger, flat
a)
(18) Sanding finger, oval
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Bosch Power Tools
Technical Data
Multi Sander
Article number
Rated power input
Orbital stroke rate preselec-
tion
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet surface
Sanding sheet surface – rect-
angular
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined ac-
cording to EN 62841-2-4.
Typically, the A-weighted noise level
of the power tool is:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a
sum) and uncertainty K determined
according to EN 62841-2-4:
a
K
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
a)
power tool is used for other applications, with different ap-
a)
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
(triax vector
h
h
1 609 92A 83M | (04.07.2022)
English | 13
PSM 200 AES
3 603 CB6 0..
W 200
●
−1
min 3000–13,000
−1
min 6000–26,000
mm 1.8
2
cm 104
2
cm 164
kg 1.4
/II
dB(A) 83 86
dB(A) 94 97
dB 3
2
m/s 6.0 7.0
2
m/s 1.5