Device Description; Assembling The Appliance - MSW -FS-350 Manual De Instrucciones

EN
q) Do not cover the ventilation openings!
r) Oil leaking from the machine should be reported
to the appropriate services or comply with legal
requirements applicable in the area of use.
s) Danger! Danger to health and the risk of explosion of
the internal combustion engine.
t) Poisonous carbon monoxide is present in the
engine exhaust. Remaining in a carbon monoxide
environment may lead to losing consciousness or
even death. Do not run the engine in a closed space.
u) Protect the engine from heat, sparks and flame. Do
not smoke in the vicinity of the engine!
v) Petrol is flammable and explosive. Before refuelling
the engine should be turned off and cooled down
w) Warning! Risk of engine damage due to wrong fuel
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The product is intended for making straight cuts in hard
surfaces, such as concrete (also reinforced), asphalt, etc., as
well as for making expansion joints in pavements.
The user is liable for any damage resulting from
unintended use of the device.

3.1. DEVICE DESCRIPTION

MSW-FS-350
13
3
12
1
5
14
2
11
8
15
10
6
4
7
9
16
1 Shifter
2 Ignition switch
3 Height adjustment knob
4 Cutting depth scale
5. Fuel tank
6 Oil drain plug
7 Cutting line guide
8 Belt cover
9 Saw blade guard
10 Space for the service key
11 Water connection
12 Hook for lifting the entire machine
13 Adjustment lever
14 Adjustment lever
15 Water supply valve
16 Bolt securing the saw blade guard
17 Water tank (not shown in the picture
- located above the lifting hook)
16
MSW-FS-500
A B
E
F
G
D
H
A. Height adjustment knob
B. Control Panel
C. Handle
D. Water connection with inlet valve
E. Water tank
F. Fuel tank
G. Saw blade guard
H. Cutting line guide
ENGINE
a
b c
d
e
i
f
h
g
j
k
l
m
Rev. 14.10.2020
a) Throttle Lever (for MSW-FS-500 on the control panel)
C
b) Silencer
c) Ignition switch
d) Starter cord
e) Spark plug
f) Air filter housing
g) Fuel valve lever
• ON – valve-inflow open
• OFF – valve-inflow closed
Rev. 14.10.2020
EN
h) Manual choke lever
• ON – switched on/choke
• OFF – off/valve open
i) Starter
j) Fuel tank cap
k) Fuel tank
l) Oil drain plug
m) Oil filler/level cap
3.2. PREPARING FOR USE
APPLIANCE LOCATION
Keep the device away from any hot surfaces. The machine
should always be used on an even, stable, fireproof surface
and out of reach of children and people with reduced
psychological, sensory and mental functions. The valve that
disables the compressed air supply should be immediately
accessible from the area where the device is being used.
Make sure that the pressure of the air supplying the device
does not exceed the recommended range.

ASSEMBLING THE APPLIANCE

• MSW-FS-350
To adjust the handles to the operator's preferred position,
loosen the adjustment levers (13 and 14).
13
14
To fit the cutting disc, make sure the machine's engine is
turned off (ignition switch is OFF). Set the machine to the
highest cutting position, then unscrew the screw securing
the blade guard (16) and remove the guard (9). Unscrew
the saw blade clamping bolt (D, right-hand thread) and fix
the saw blade by keeping it stationary and tightening the
clamping bolt (D) again. Pay attention to the arrow on the
blade guard showing the direction of rotation of the blade
while the machine is running. When fitting/replacing the
saw blade, check that the mounting flanges (C and E) are
undamaged. Replace the saw blade guard (9) and tighten its
screw (16). Make sure that the cutting disc is aligned with the
cutting line guide (7) - if not, align it by adjusting the guide.
17