DeWalt D24000 Manual De Instrucciones página 35

• DO - Shut off power, disconnect cord from power source
and wait for the saw cutting wheel to stop before
servicing, adjusting tool or changing cutting wheel.
• DON'T - Attempt to operate on anything but designated
voltage. Incorrect voltage may result in shock, fire, or
unpredictable operation.
• DON'T - Operate unless all knobs and clamp handles
are tight.
• DON'T - Use cutting wheels larger or smaller than those
which are recommended.
• DON'T - Force cutting action. Allow motor to reach full
speed before cutting. Stalling or partial stalling of motor
can cause major damage.
• DON'T - Use metal cutting abrasive wheels. The excessive
heat and abrasive particles generated by them will
damage the saw.
• DO - Use continuous rim wheels only, no serrated edges.
• DON'T - Allow anyone to stand behind saw.
• DON'T - Place either hand in the cutting wheel area when
the saw is connected to the power source.
• DON'T - Use cutting wheels rated less than 5000 R.P.M.
• DON'T - Place hands closer than 3" (76 mm) from the saw
cutting wheel.
• DON'T - Reach behind or underneath the saw unless it is
turned off and unplugged.
• DON'T - Move either hand from saw or workpiece until the
cutting wheel has stopped.
• If the plug or receptacle does get wet. DON'T unplug the
cord. Disconnect the fuse or circuit breaker that supplies
power to the tool. Then unplug and examine for presence
of water in the receptacle.

WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
All manuals and user guides at all-guides.com
•

For your convenience and safety, the following warning
labels are on your Wet Tile Cutter.
On Column

•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
On Cutting Wheel Cover

On Cart

Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
WARNING: FOR YOUR OWN SAFETY, READ
INSTRUCTION MANUAL BEFORE OPERATING tile Saw.
ALWAYS use EYE PROTECTION.
Always use proper respiratory protection.
Keep hands out of path of cutting wheel.
Use tool only with smooth edge cutting wheels free of
openings and grooves.
Do not operate saw without covers in place.
Always tighten adjustment knobs before use.
Do not perform any operation freehand.
Never reach in back of cutting wheel.
Never cross arms in front of cutting wheel.
Turn off tool and wait for cutting wheel to stop before
moving work piece or changing settings.
Disconnect power before changing cutting wheels,
servicing or cleaning.
To reduce risk of injury always plug tool into a GFCI
receptacle and test GFCI before use.
Always return cutting wheel to proper position before
turning on saw.
Use splash guard for every operation for which it can
be used.
Replace damaged cutting wheel before operating.
Do not expose to rain or use in damp locations.
Never use pan heater or other heater source for heating
water. Damage to the tool, fire or personal injury
could result.
Think! You can prevent accidents.
CAUTION: Properly secure cover with both screws
before use.
WARNING: To reduce the risk of injury, always verify
the cutting wheel is adjusted to the correct height
and location in the center of the cart groove before
operating saw.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ENGlIsH
33