Tool Placement - DeWalt D24000 Manual De Instrucciones

To Attach the Edge Guide (Fig. L)
1. Place edge guide 10 on the cutting cart assembly
2. Turn the edge guide lock 23
Specifications
B3
Voltage 120 V
Power 1600 W
Frequency 60 Hz
Amps 15 A
RPM 4200
Depth of Cut 3–1/8" (80 mm)
Miter Angles 22.5º and 45º
Cutting Wheel sizes 7" (178 mm), 8" (203 mm),
9" (229 mm) and
10"(254 mm) Continuous
Rim Cutting wheels and 6"
(152 mm) Profile Wheel
OPERATION

WARNING: Always observe the safety instructions
and applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.

Tool Placement

Place stand (D24001, see Accessories) on a level surface.
Place the saw into the stand as shown in Figure T.
If not using a stand, place saw on a level surface.
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause
loss of power and overheating. All D
tested; if this tool does not operate, check the power supply.
• Always plug saw into a GFCI receptacle.
• Always plug extension cord into a GFCI receptacle.
• Use only extension cords that are intended for outdoor
use. These extension cords are identified by a marking
"Acceptable for use with outdoor appliance; store
indoors while not in use."
• Use only extension cords having an electrical rating not
less than the rating of the product.
• Do not use damaged extension cords. Examine
extension cord before using and replace if damaged.
• Do not abuse extension cords and do not yank on any
cord to disconnect.
• Keep cord away from heat and sharp edges.
• Always disconnect the extension cord from the
receptacle before disconnecting the product from
the extension cord.
All manuals and user guides at all-guides.com
On/Off Switch (Fig. A, F)

8 .
clockwise to tighten.
Fig. F
To turn the wet tile cutter on, lift up the on/off switch
The wet tile saw locks on automatically. To turn the tool off,
push the on/off switch down. A hole is provided under the
switch for insertion of a padlock to deter unauthorized use.
Water Nozzles (Fig. G–I)
Water nozzles
water for cutting and maximum capacity with the minimum
amount of overspray and mist. The adjusting lever
allows easy adjustment of nozzles to desired position.
1. Optimum position for minimum overspray (Fig. G).
2. Water nozzles can be fully retracted to allow for
3. "Off Cutting Wheel" position to eliminate water
Fig. G
WALT tools are factory
e
Cutting Wheel Alignment
To Check Alignment (Fig. J)
1. Place a 90º framing square on the cutting cart fence
2. Push the cutting cart along the cutting wheel to
3. If the gap is not consistent, see the Adjustments section
WARNING: To avoid the possibility of the appliance
plug or receptacle getting wet, position the wet tile
saw to one side of a wall mounted receptacle to
prevent water from dipping onto the receptacle or
plug. The user should arrange a "drip loop" in the
cord connecting the saw to a receptacle (Fig. F). The
"drip loop" is that part of the cord below the level of
the receptacle, or the connector if an extension cord
is used, to prevent water traveling along the cord and
coming in contact with the receptacle.
are adjustable to provide maximum
13
maximum capacity (Fig. H).
overspray between cuts and for blade change (Fig. I).
Fig. H
22
13
determine if the gap along the framing square is
consistent along the length of the stroke.
of this manual.
ENGlIsH
1 .
22
Fig. I
.
24
37