Battery Removal/Installation - Hitachi Koki DS 9DVF3 Instrucciones De Manejo

4. Battery (EB1814SL, BCC1815, EB1820L)
(For DS18DVF3)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
○ Drilling of various metals.
○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch (1 pc.
or 2 pcs.) to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
〈UC9SD/UC12SD〉
Before using the driver drill, charge the battery as follows.
1. Insert the battery into the charger
Insert the battery fi rmly while observing its direction,
until it contacts the bottom of the charger (See Fig. 3).
CAUTION
The UC9SD and UC12SD models are the
exclusively designed
charge batteries except the specifi ed batteries.
It is possible to insert the batteries other than the
specifi ed into the charger and some of them may
light up the pilot lamps. However, you are requested
to exercise utmost caution not to charge batteries
other than specifi ed ones because these can not
only be charged but also such actions can result in
the malfuntion of chargers.
2. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger (the
pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from the receptacle and check the battery
mounting condition.
About 60 minutes is required to fully charge the battery
at a temperature of about 20°C. The pilot lamp goes off
to indicate that the battery is fully charged.
The battery charging time becomes longer when a
temperature is low or the voltage of the power source is
too low.
When the pilot lamp does not go off even if more
than 120 minutes have elapsed after starting of the
charging, stop the charging and contact your HITACHI
AUTHORIZED SERVICE CENTER.
charger. These cannot
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may not
light up. At that time, cool the battery fi rst, then start
charging.
3. Disconnect the charger power cord from the
receptacle
4. Hold the charger fi rmly and pull out the battery
NOTE
After charging, pull out batteries from the charger fi rst,
and then keep the batteries properly.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might be
low when using them the fi rst and second time. This is
a temporary phenomenon, and normal time required for
recharging will be restored by recharging the batteries
2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
〈UC18YG〉
Before using the driver drill, charge the battery as follows.
1. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger.
2. Insert the battery into the charger
Insert the battery fi rmly while observing its direction,
until it contacts the bottom of the charger (See Fig. 4)
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from the receptacle and check the battery
mounting condition.
(1) Regarding the temperatures of the rechargeable
battery
The temperatures for rechargeable batteries are as
shown in Table 1.
Table 1 Recharging ranges of batteries
Rechargeable batteries
EB912S, EB914S, EB9B,
EB1212S, EB1214S,
BCC1215, EB1220BL,
EB1412S, EB1414S,
BCC1415, EB14B,
EB1814SL, BCC1815,
EB1820L
English
Temperatures at which the
battery can be recharged
0°C – 45°C
9