Tabla de contenido
Publicidad
Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.6.4. INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
- First set of operations:
Check the connection between the power and bat-
tery connector, located under the control panel.
Put the ignition key in and turn it.
Check battery charge status via the control unit and,
if sufficient, operate the brush control key. Now open
the solution cock by lowering the detergent dosage
lever which is at the back of the machine, lower
the brushing unit by levering with your foot on the
brush plate control lever. Move forwards, pulling the
forward lever up .
Allow the detergent solution to work on the dirt
according to what is indicated in the information
relative to the detergent used.
- Second set of operations:
Proceed as explained in the previous "Direct Washing"
paragraph (7.7.3) to also proceed with drying the floor.
Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.6.5. POST-SCRUBBING OPERATIONS
Cut off the supply of detergent.
Lift the brush unit and turn off the brush motor.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks (as de-
scribed in 7.4 and 7.5).
Empty and clean the tanks (see sections 7.4 and 7.5).
Turn off the machine using the key and remove it
from the control panel.
If necessary, charge the battery (see the relative sec-
tion).
7.
MAINTENANCE INFORMATIONS
• Turn the key, remove it from the control panel and
disconnect the battery from the machine wiring.
☞ All work on the electrical system as well as all main-
tenance and repair operations (especially those not
explicitly described in this manual) should be carried
out only by authorised service centres or by speciali-
sed technical personnel who are experts in the sector
and in the pertinent safety regulations.
Performing regular maintenance on the machine, and
carefully following the manufacturer's instructions, is
the best guarantee for obtaining the best performan-
ces and extended machine service life.
7.1.
TANKS
Drain the two tanks as described in the relative sections.
Remove any solid dirt by filling and draining the tanks
until all dirt has been eliminated: use a washing hose
or similar tool to do this.
• Water hotter than 50°, a high-pressure cleaner
or excessively powerful sprays may damage the
tanks and the machine.
Leave the plugs of the tanks open (only while the ma-
chine is not being used) so that they can dry and thus
prevent the formation of foul odours.
7.2.
SUCTION HOSE
Detach the suction hose from the squeegee.
Now you can wash the hose and remove any obstruc-
tions.
Firmly insert the hose on the squeegee body.
7.3.
SQUEEGEE
• Do not handle the squeegee with bare hands: wear
gloves and any safety clothing needed to carry out
the operation.
Detach the squeegee from the machine and clean it
under running water using a sponge or a brush.
Check the efficiency and the wear on the strips in con-
tact with the floor. They are designed to scrape the
film of detergent and water on the floor and to isolate
that portion of the surface to enhance the vacuum of
the suction motor: this ensures that the machine will
dry very efficiently. Working constantly in this manner
tends to round or to deteriorate the sharp edge of the
strip, thus reducing drying efficiently. This is why the
squeegee strips must be replaced.
To replace the worn blades, follow the instructions in
the relative section. Turn the blades around to wear
down the other sharp corners or to install new ones.
7.4.
ACCESSORIES
Remove and clean the brushes or the scraper disks.
• To avoid damaging the floor and the machine, ca-
refully check if foreign matter, such as metallic parts,
screws, chips, cords or similar items, has become jam-
med.
Check that the brushes are flat as they work on the
surface (check for any irregular wear on the brushes
or on the abrasive disks). If necessary, adjust the slant
of the action on the floor.
Use only the accessories recommended by the manu-
facturer: other products may reduce operating safety.
7.5.
MACHINE BODY
Use a sponge or a soft cloth to clean the exterior of
the machine and, if necessary, a soft brush to elimi-
nate tough dirt. The machine's shockproof surface
is rough to make it harder to see scratches caused
during use. However, this does not make it easier to
remove tough stains on the surface. Steam machines
can be used but it's prohibited to use hoses with run-
ning water or a high-pressure cleaner.
33
Publicidad
Tabla de contenido
