Manuales relacionados para Kyocera PF-810
Resumen de contenidos para Kyocera PF-810
- Página 1 INSTALLATION GUIDE GUIDE D’INSTALLATION GUÍA DE INSTALACION INSTALLATIONSANLEITUNG GUIDA ALL’INSTALLAZIONE 安装手册 설치안내서 設置手順書 PF-810...
- Página 3 D(M3x12) G(M4x20) E. Stopper R........... 1 Be sure to remove any tape and/or cushioning English F. Stopper L ........... 1 materials from the parts supplied. Supplied parts G. S Tite screws M4 × 20 ......4 A. Paper feeder..........1 H.
- Página 4 Procedure Place the machine (2) on the paper feeder (A) 2.Remove the lower paper cassette (4) from Before starting installation, be sure to turn the the machine. so that the pins (1) at the rear left and rear right main power switch of the machine off, and of the paper feeder (A) are aligned with the holes in the base of the machine.
- Página 5 (M3x12) 3.Secure the machine (2) to the paper feeder 5.Install the retainer (C) in the location as 6.Open the lower right cover (5) on the (A) with the 2 pins (B). shown in the figure using 2 S Tite screws M3 machine.
- Página 6 8.Remove the strap (7) from the shaft (8) and 9.Lift up the guide (3) until it clicks into place. 12.Turn the adjusters on each corner (9) until remove lower right cover (5). they reach the floor and then secure the 10.Close the paper feeder right cover (6) and paper feeder.
- Página 7 G(M4x20) G(M4x20) 13.Pull out the right cassette (10) and the left 15.Select holes (13) and install each stopper (E,F) with 2 S Tite screws M4 × 20 (G) so that the stop- cassette (11) from the paper feeder (A). pers will be grounded on the floor. Remove the lift plate stopper (12) from each cassette and attach it to the storage location.
- Página 8 Setting paper size plate Changing paper size (metric specifications 1.Pull out the cassette of the paper feeder. Insert the paper size plate (H) into the size dis- only) 2.Turn the front lock lever (14) 90° and remove play slot. At shipment, Letter is set for inch models and A4 the front deck cursor (15).
- Página 9 3.Move the front deck cursor (15) so that it is aligned with the size indicators on the top (17) and 6.Release the hook (19) and remove the deck bottom (16) of the cassette. trailing edge cursor (20). 4.Turn the front lock lever (14) 90° to lock it. 5.Move the rear deck cursor (18) in the same way.
- Página 10 0.5〜1.5mm 7.Lift up the sub-cursor (21). Adjusting the cursor width 8.Align with the size indicator (22), engage the 1.Load paper in the cassettes. hook (23) and install the deck trailing edge 2.If the gap between the front deck cursor (15) and the paper (24) is outside the 0.5 to 1.5 mm cursor (20).
- Página 11 3.Insert a Philips-head screwdriver into the 2 long slots (25) in the front deck cursor (15) and loosen 4.Retighten the 2 adjusting screws (26). the 2 adjusting screws (26). Then move the front deck cursor (15). 5.Check that the gap between the front deck cursor (15) and the paper is between 0.5 and 1.5 mm.
- Página 12 20±2.5mm b<20mm b>20mm Adjusting the leading edge timing The reference value for the leading edge timing is 20 ±2.5 mm at position (1) in the sample image (a). If the timing is outside this range, perform the fol- lowing adjustment. 1.Set maintenance mode U034, select [LSU Out Top Full/Start Position] and [Cassette] or [Cassette3/Cass3]/[Cassette4/Cass4].
- Página 13 d<0mm d>0mm Adjusting the center line The reference value for the center line (2) is ±2.0 mm or less at position (3) in the sample image (c). If the center line position is outside this range, per- form the following adjustment. 1.Set maintenance mode U034, select [LSU Out Left/Center Line] and [Cassette3/Cass3] or [Cassette4/Cass4].
- Página 14 MEMO...
- Página 15 MEMO...
- Página 16 2021.11 303PC5671003...