Manuales relacionados para Kyocera DP-7160
Resumen de contenidos para Kyocera DP-7160
- Página 1 DP-7160 DP-7170 INSTALLATION GUIDE GUIDE D’INSTALLATION GUÍA DE INSTALACION INSTALLATIONSANLEITUNG GUIDA ALL’INSTALLAZIONE...
- Página 2 (EN) In case of installing it in the following product, install it referring to the installation procedures described in the service manual. (FR) En cas d’ installation dans le produit suivant, reportez-vous aux procédures d’ installation figurant dans le manuel de service. (ES) En caso de instalar la unidad en el siguiente producto, consulte los procedimientos de instalación que se describen en el manual de servicio para instalarla.
- Página 3 B(L) B(R) C(M4x14) C(M4x14) H(M3x8 BLACK) K(M3x8) K(M3x8) H(M3x8 BLACK) 120V (North America / 230V (Europe) 120V (North America / 230V (Europe) 100V For Taiwan Latin America) Latin America) (EN) Be sure to remove any tape and/or cushioning materials from the parts supplied. (FR) Veillez à...
- Página 4 C(M4x14) C(M4x14)
- Página 5 (M3x8 BLACK) H(M3x8 BLACK)
- Página 8 K(M3x8) K(M3x8) K(M3x8) K(M3x8) K(M3x8) K(M3x8) K(M3x8) K(M3x8)
- Página 10 20mm 20mm 20mm 20mm [Operation check] 1.To check the machine operation, prepare original (a) where 4 lines (b) are drawn 20 mm from the edges of the A3 sheet and 1 line (c) is drawn at its center. 2.Connect the power plug of the MFP into the wall outlet and turn the main power switch on. 3.Set the original (a) on the DP and perform a test copy to check the operation and the copy example.
- Página 11 20mm 20mm 20mm 20mm 4.Compare original (a) with the copy example. If the gap exceeds the reference value, perform the following adjustments according to the type of the gap. Check images of the DP after checking and adjusting images of the MFP. For details, see the service manual. NOTICE: If there is any image fogging, adjust the U068 DP scanning position.
- Página 12 Be sure to adjust in the following order. If not, the adjustment cannot be performed correctly. For checking the angle of leading edge, see page 12. <Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm For checking the angle of trailing edge, see page 15. <Reference value>...
- Página 13 For checking the leading edge timing, see page 20. <Reference value> Within ±2.5 mm For checking the center line, see page 22. <Reference value> Simplex copying: within ±2.0 mm; Duplex copying: within ±3.0 mm When using the original for adjustment, automatic adjustment of magnification, leading edge timing and center line can be performed at a time.
- Página 14 [Checking the angle of leading edge] 1.Check the horizontal gap between line (1) of original (a) and line (2) of copy example positions. If the gap exceeds the reference value, adjust the gap according to the following procedure. <Reference value> For single copying: The horizontal gap of line (2) should be within ±3.0 mm. For duplex copying: The horizontal gap of line (2) should be within ±4.0 mm.
- Página 15 C(M4x14) C(M4x14) C(M4x14) C(M4x14) Remove the left hinge cover (F) and the angle control fitting (E). Loosen the 2 M4 × 14 screws (C) on the left and right fixing fittings (B1)(B2). 3.Turn adjusting screw (3) at the rear side of the right hinge to adjust the DP position. For copy example (d): Turn the adjusting screw counterclockwise and move the DP to the inner side.
- Página 16 4.Perform a test copy. 5.Repeat the steps above until the gap of line (2) of copy example shows the following reference values. <Reference value>For single copying: The horizontal gap of line (2) should be within ±3.0 mm. For duplex copying: The horizontal gap of line (2) should be within ±4.0 mm. 6.After adjustment is completed, retighten two M4 ×...
- Página 17 3mm/4mm 3mm/4mm [Checking the angle of trailing edge] 1.Check the gap between line (1) of original (a) and line (2) of copy example. If the gap exceeds the reference value, perform the following adjustment. <Reference value> For simplex copying: Within ±3.0 mm For duplex copying: Within ±4.0 mm [Vérification de l’angle du bord arrière] 1.Vérifiez l’écart entre la ligne (1) de l’original (a) et la ligne (2) de l’exemple de copie.
- Página 18 Amount of change per scale: Approx. 0.5 2.Open the upper cover (3) of the DP (A). 4.Adjust the height of DP. mm (10) 3.Remove the 3 TP screws (4) and the screw Loosen the nut (8). Retighten the nut (8). (5), and remove the strap (6) from the rear For copy example (f): Loosen the adjusting 5.Refit the rear cover (7) removed in step 3.
- Página 19 3mm/4mm 3mm/4mm 6. Remove the original mat (M) and refit it (see steps 6 on page 2). 7.Make a proof copy again. 8.Repeat steps 1 to 6 until line (2) of copy example shows the following the reference values. <Reference value> For simplex copying: Within ±3.0 mm For duplex copying: Within ±4.0 mm Retirez le tapis d’original (M) et remettez-le en place (Reportez-vous aux étapes 6 à...
- Página 20 -1.5% +1.5% [Checking the magnification] 2. Use the maintenance mode U070 to adjust the sub scan direction Sub Scan(F): Adjusts the scanner sub-scan magnification (front side) 1.Check the gap between line (1) of original (a) and line (2) (3) of copy Sub Scan(B): Adjusts the scanner sub-scan magnification (rear side) example.
- Página 21 -1.5% +1.5% 3.Adjust the values. 5. Repeat the steps 2 to 4 above until the gap of line (2) (3) of copy example shows the reference value. For the shorter length copy example (h)(j): Increases the value. <Reference value> For the longer length copy example (i)(k): Decreases the value. For the sub-scan direction, vertical gap of line (2): within ±1.5% Amount of change per step: 0.1 % For the main-scan direction, horizontal gap of line (3): within ±1.5%...
- Página 22 2.5mm 2.5mm [Checking the leading edge timing] Use the maintenance mode U071 to adjust the timing. 1.Check the gap between line (1) on original (a) and line (2) of copy Front Head: Adjusts the leading edge timing (front side) example. If the gap exceeds the reference value, adjust the gap Front Tail: Adjusts the trailing edge timing (front side) according to the following procedure.
- Página 23 2.5mm 2.5mm 3.Adjust the values. 5.Repeat the steps 2 to 4 above until the gap of line (2) of copy example For the shorter leading edge timing, copy examples (l): Decreases the shows the reference value. value. <Reference value> For the longer leading edge timing, copy examples (m): Increases the Vertical gap of line (2): within ±2.5 mm value.
- Página 24 2mm/ 2mm/ [Checking the center line] 2.Use the maintenance mode U072 to adjust the timing. 1.Check the gap between center line (1) on original (a) and center line Front: Adjusts the center line (front side) (2) of copy example. If the gap exceeds the reference value, adjust the CIS: Adjusts the CIS center line gap according to the following procedure.
- Página 25 2mm/ 2mm/ 3. Adjust the values. 5.Repeat the steps 2 to 4 above until the gap of line (2) of copy example If the center moves more front, copy example (n): Decreases the value. shows the reference value. If the center moves inner, copy sample (o): Increases the value. <Reference value>...
- Página 26 [Automatic adjustment using the original for adjustment] 4.Set the original on the DP face down and press the Start key to carry If there is no DP auto adjustment original. out rear-side adjustment. 1.Set the maintenance mode U411 and press [DP Auto Adj] to output the appears on the display, the adjustment is completed.
- Página 27 149 1mm A(149 5mm) 74 1mm Using a DP auto adjustment original 3.If “OK” appears on the display, the adjustment is completed. 1.Direct F and R of the DP auto adjustment original upward, and set the If the number appears, the adjustment failed. Check the original set original from the place where F and R are marked.
- Página 28 149 1mm A(149 5mm) 74 1mm 4.After completing the surface adjustment, direct F and R of the DP auto 6.If “OK” appears on the display, the adjustment is completed. adjustment original downward and set the original by inserting the side If the number appears, the adjustment failed.
- Página 29 MEMO...
- Página 30 MEMO...
- Página 32 2021.11 303TC5671003...