DeWalt DCD1623 Manual De Instrucciones página 15

Push the power switch 1
nOTE: The tool will not run unless magnet is at 100%
engagement. An orange light will illuminate indicating the
magnet is not fully engaged.
Press the switch down (0) to shut down the tool.
E‑Clutch ® System and Low Voltage
Indicator LED (Fig. A)
The DCD1623 is equipped with the D
system. This feature senses the motion of the tool and shuts
the tool down if necessary. The E‑Clutch® indicator
illuminate red to indicate status.
The working LED on the front of the magnetic base
flash to alert the user of low voltage conditions.
inDiCATOR DiAgnOsis
OFF Tool is functioning
normally
RED E‑Clutch ® System
SOLID has been activated
(ENGAGED)
ORANGE The magnet
SOLID engagement lever
is not in the 100%
position with the
power switch on.
WHITE Low voltage
FLASHING battery conditions
Drilling with Annular Cutters
1. Annular cutters only cut material at the periphery of the
hole, rather than converting the entire hole to shavings.
As a result the energy required to make a hole is lower
than for a twist drill.
2. When drilling with an annular cutter, it is not necessary
to drill a pilot hole.

CAUTION: Do not touch the cutter or the parts close
to the cutter immediately after operation, as they may
be extremely hot and cause burns to the skin. Ensure
nobody is in the work area where the metal core
is ejected.
Drilling Conditions
The ease with which material can be drilled is dependent
on several factors including tensile strength and abrasion
resistance. Hardness and /or strength is the usual criterion,
wide variations in machine ability can exist among material
showing similar physical properties. The drilling conditions
are dependent on requirements for tool life and surface
finish. These conditions are further restricted by the rigidity of
the tool and the workpiece, lubrication and machine power
available. The harder the material the lower the cutting
speed. Some materials of low hardness contain abrasive
substances leading to rapid cutting edge wear at high
speeds. Feed rates are governed by rigidity of set‑up, volume
up (i) to run the tool.
WALT E‑Clutch®
e
sOlUTiOn
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will
function normally when the trigger
is depressed again and the indicator
light will go out.
Move the magnet engagement
lever to the 100% position.
Suspend use of the tool and replace
with fully charged battery.
of material to be removed, surface finish and available
machine power.
Drilling a Hole (Fig. A)
1. Always apply an appropriate cutting fluid/ coolant on the
cutting area.
2. Lower the guard
be drilled.
3. Make sure the drill point or cutter pilot is properly
installed over the spot to be drilled.
4. Push the power switch
will
24
5. Slowly feed the accessory into the workpiece using the
feed handle
20 will
6. At the start of the cut, apply light pressure to allow the
accessory to perform the initial groove.
7. Continue applying sufficient pressure to achieve a
smooth progressive cut. Do not force.
8. Take extra care when the accessory is about to break
through the surface to prevent splintering.
9. Always turn off the motor, the magnet and the power,
in that particular order, when work is finished and before
removing the battery.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Tool Connect™ Chip (Fig. O)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
so that it screens the surface to
10
up (i) to run the tool.
1
6 .
that hold the Tool
34
into the tool.
36
English
35 .
13