Clip Connection; Operation - Menzer VCH 530 PRO Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 42
non-inflammable dusts with workplace limit values
(AGW).
● Unused flat fold filters may only be stored and trans-
ported in their packaging (cardboard box).
WARNING
Danger from dust that is harmful to your health
Respiratory sicknesses through inhalation of dust.
Do not vacuum without a correctly installed safety filter
bag/dust bag, otherwise a danger to health from in-
creased fine dust emission is present.
Installing the safety filter bag
1. Unlock and remove the suction head.
2. Attach the safety filter bag.
Illustration C
3. Pull the safety filter bag over the container.
Illustration D
4. Fit and lock the suction head.
Installing the dust bag
Note
The dust bag opening must be pulled fully over the suc-
tion hose port.
1. Unlock and remove the suction head.
2. Fit the dust bag.
Illustration E
3. Pull the dust bag over the container.
4. Fit and lock the suction head.
Wet vacuum cleaning
DANGER
Danger from dust that is harmful to your health
Respiratory sicknesses through inhalation of dust.
No dusts harmful to health may be vacuumed when per-
forming wet vacuum cleaning.
Installing the squeegees
1. Remove the brush strips from the floor nozzle (spe-
cial accessory).
Illustration F
2. Install the squeegees.
Closing the suction connection
1. Fit a plug exactly into the suction connection.
Illustration G
2. Push the plugs in until they engage.
Removing the safety filter bag
● The safety filter bag must always be removed when
vacuuming wet substances.
1. Unlock and remove the suction head.
2. Fold up the safety filter bag.
Illustration H
3. Take off the protective film and close the ventilation
hole with a self-adhesive tab.
4. Pull the safety filter bag out towards the back.
Illustration I
5. Seal the suction connection opening of the safety fil-
ter bag tightly with closing slides.
6. Close the safety filter bag tightly with the attached
cable tie.
Illustration J
7. Remove the safety filter bag.
8. Clean the container inside with a moist cloth.
9. Dispose of used safety filter bag in dust-tight bag in
accordance with statutory regulations.
10. Fit and lock the suction head.
16
Removing the dust bag
● The dust bag must always be removed when vacu-
uming wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag.
Illustration K
3. Pull the dust bag opening towards the rear over the
suction hose port.
4. Seal the dust bag tightly with cable ties under the
suction connection opening and the ventilation hole.
5. Remove the dust bag.
6. Clean the container inside with a moist cloth.
7. Dispose of the dust bag in accordance with statutory
regulations.
8. Fit and lock the suction head.
Draining the waste water
VCH 550 PRO only:
1. Drain the waste water via the drain hose.
Illustration L
● We recommend switching off the "Automatic filter
dedusting" function when vacuuming wet dirt with
the crevice nozzle (special accessories) or when
sucking mainly water out of a container.
● The device switches off automatically when the
maximum fluid level is reached.
● When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not au-
tomatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
● On completion of wet vacuum cleaning: Clean the
flat fold filter using the dedusting function. Clean the
electrodes with a brush. Clean the container with a
moist cloth and dry it off.
The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 35 mm can be
connected.
Illustration M
Device OFF
Device ON
Automatic filter dedusting: OFF
Device ON
Automatic filter dedusting: maximum in-
terval
Device ON
Automatic filter dedusting: minimum in-
terval
Switching on the device
1. Connect the mains plug.
2. Set the turn switch to the desired program.
Adjusting the suction power
1. Adjust the suction power (min-max) via the rotary
control.
English
General

Clip connection

Operation

Turn switch

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Vch 550 pro

Tabla de contenido