Safety Regulations - EINHELL TC-BD 450 Manual De Instrucciones

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fire and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
General safety instructions for electric tools
1. Keep your work area tidy!
- An untidy work area invites accidents.
2. Check the working conditions!
- Do not expose electric tools to rain.
- Never use electric tools in damp or wet lo-
cations.
- Make sure there is good lighting.
- Do not use electric tools near flammable
liquids or gases.
3. Guard against electric shock!
- Avoid body contact with earthed compo-
nents.
4. Keep other persons away!
- Do not allow other persons, particularly
children, to touch the tool or cable. Keep all
persons out of your work area.
5. Store tools in a safe place!
- When tools are not in use they should be
stored in a dry, locked room out of children's
reach.
6. Do not overload your tools!
- Tools work better and safer when used
within their quoted capacity range.
7. Use the right tool!
- Never use tools or attachments with insuf-
ficient power for the job in hand.
- Never use tools on jobs for which they
were not intended. For example, do not use
Anl_SA_TC_BD_450_SPK8.indb 28 Anl_SA_TC_BD_450_SPK8.indb 28
GB
a hand-held circular saw to cut down trees or
lop off branches.
8. Wear suitable work clothes!
- Do not wear loose clothing or jewelry as
they may get caught in moving parts.
- Non-slip shoes are recommended when
working outdoors.
- Wear a hair net if you have long hair.
9. Use personal safety equipment!
- Wear safety goggles
- Use a dust mask when working on dusty
jobs
10. Connect up a vacuum extraction system!
- If there are provisions for connecting up a
vacuum extraction system, make sure that
such a system is fitted and in use.
11. Do not mis-use the cable!
- Do not carry the tool by its cable or pull on
the cable to remove the plug from the socket-
outlet. Protect the cable from heat, oil and
sharp edges.
12. Secure your workpiece!
- Use clamps or a vise to hold the workpiece
securely. This is safer than using your hand
and will enable you to operate the machine
with both hands.
13. Avoid abnormal working postures!
- Make sure you stand squarely and keep
your balance at all times.
14. Look after your tools!
- Keep your tools sharp and clean for better
and safer performance.
- Follow the instructions for maintenance
work and for changing any attachments.
- Check the plug and cable regularly and, if
damaged, have them replaced by an autho-
rized specialist.
- Check the extension cable regularly and
replace it if damaged.
- Keep handles dry and free from oil and gre-
ase.
15. Always pull out the power plug:
- When the tool is not being used, before
carrying out any maintenance work and when
changing attachments such as blades, bits
and cutters of any kind.
16. Remove adjusting keys and wrenches!
- Make sure that all keys and adjusting wren-
ches are removed from the tool before swit-
ching it on.
17. Avoid unintentional starting!
- Make sure that the switch is in OFF position
when inserting the power plug.
18. When using an extension cable outdoors:
- Check that it is approved for outdoor duty
- 28 -
19.07.2022 13:18:28 19.07.2022 13:18:28