Special Safety Instructions; Extension Cable - EINHELL TC-BD 450 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

and is marked accordingly.
19. Be alert at all times!
- Watch what you are doing. Use common
sense. Do not operate the tool if your mind is
not on your work.
20. Check the tool for damage!
-
Each time before re-using the tool, carefully
check that the guards or any slightly dama-
ged parts are working as intended.
-
Check that the moving parts are in good wor-
king order, that they do not jam, and that no
parts are damaged. Make sure that all parts
are fitted correctly and that all other operating
conditions are properly fulfilled.
-
Unless otherwise stated in the operating in-
structions, damaged guards and parts have
to be repaired or replaced by an authorized
service center.
- Have damaged switches replaced by a cus-
tomer service workshop.
- Never use any tool if its switch cannot be
turned off and on.
21. IMPORTANT!
- The use of any accessory or attachment
other than those recommended may involve a
risk of injury for you personally.
22. Have repairs carried out only by a quali-
fied electrician!
- This electric tool complies with the pertinent
safety regulations. Repairs are to be carried
out only by a qualified electrician using origi-
nal replacement parts or the user may suffer
an accident.

Special safety instructions

The pillar drill was designed in such a way so as
to all but eliminate potential hazards when the
machine is properly used. However, there are a
few safety precautions to observe in order to en-
sure that all residual hazards are ruled out.
Ensure proper voltage
The voltage must comply with the specifications
on the rating plate.
Use a socket-outlet with earthing contact
The device may only be operated from an outlet
with the properly installed earthing contact.

Extension cable

The cord cross section of an extension cable
must measure at least 1.5 mm2. Always comple-
tely unwind a cable reel prior to use. Check the
cable for defects.
Anl_SA_TC_BD_450_SPK8.indb 29
Anl_SA_TC_BD_450_SPK8.indb 29
GB
Protection against electrical shock
Keep the device away from moisture. The device
must neither be damp nor be operated in a humid
environment. Prior to every use, check the device
and the mains cable with plug for damage. Avoid
bodily contact with earthed parts e.g. pipes, hot
elements, etc.
Protection against fire and explosion
There are spark producing components inside
the device. Do not use the device in the vicinity of
combustible liquids or gases. Otherwise there is a
risk of fire or explosion.
Handle the device with care
Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges. Keep your tools sharp and clean so that
you can work efficiently and safely. Follow the
maintenance regulations and the instructions for
changing tools.
Wear suitable work clothes and personal pro-
tection equipment
Loose clothing is not suitable, as it can be caught
by moving parts, causing you to become ent-
angled. Wear a hair net if you have long hair. As
a general rule, jewelry should not be worn when
working with machine tools. Ensure that you wear
safety goggles. Not doing so could result in eye
injury.
Keep your work area neat and tidy
Disorder in the work area can easily lead to acci-
dents. Do not leave any tools, objects, or cable in
the direct vicinity of the work area, as this poses
a tripping hazard! Ensure that there is sufficient
lighting.
Watch out for other persons
Watch out for other persons (especially children)
when using the device, and keep them away from
your work area. Do not let anyone touch the de-
vice or the power cable.
Store the tools in a safe location
Store unused devices in a dry, locked location
that is out of the reach of children.
Avoid overloading the device
Operate the device only within the specified out-
put range. Do not use any low-powered machines
for heavy duty work. Do not use tools to perform
work for which they were not intended.
- 29 -
19.07.2022 13:18:28
19.07.2022 13:18:28

Publicidad

Tabla de contenido
loading

Tabla de contenido