Important - EINHELL HEROCCO 18/20 Manual De Instrucciones

5.3. Inserting a tool (Fig. 4)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the equipment.
•
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
•
Turn and push the dust-free tool into the tool
mounting (b) as far as it will go. The tool will
lock automatically.
•
Check that the bit is locked in placed by
pulling on it.
5.4. Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and
remove the tool.
6. Operation
6.1 Drill / Impact drill / Chisel selector switch
(Fig. 6)
•
For drilling, press the button (E) on the rotary
switch (2) and simultaneously turn the rotary
switch (2) to position A.
•
For impact drilling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position B.
•
For chiseling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position C.
•
In switch position C the chisel is not locked.
•
For chiseling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position D.
•
The chisel is locked in position D.

Important!

You need apply only slight contact pressure for
impact drilling. Excessive contact pressure will
place unnecessary strain on the motor. Check drill
bits at regular intervals. Sharpen or replace blunt
drill bits.
6.2 Changeover switch (Fig. 7)
Using the changeover switch (3) above the On/Off
switch (4) you can select the direction of rotation
of the equipment and lock the equipment so that
it cannot be switched on accidentally. You can
select between clockwise and counter-clockwise
rotation. To avoid causing damage to the gearing,
the direction of rotation must only be changed
when the equipment is at a standstill. When the
changeover switch (3) is in the middle position,
Anl_Herocco_18_20_SPK7_USA.indb 12 Anl_Herocco_18_20_SPK7_USA.indb 12
EN
the On/Off switch (4) is blocked.
Danger!
To avoid danger, the machine must only be
held using the two handles.
Otherwise you may suff er an electric shock if you
drill into electric cables!
6.3 On/Off switch (Fig. 7)
Infi nitely variable speed control is possible with
the On/Off switch (4). The further you push the
switch, the higher the speed of the equipment.
Switching on:
Press the On/Off switch (4).
Switching off :
Release the On/Off switch (4).
6.4 LED light (Fig. 1)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
6.5 screws
It is advisable to use self-centering screws (e.g.
cross recessed head) as these will enable you to
work safely and reliably. Always make sure that
the bit used is of the same size and shape as the
screw.
6.6 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.7 Battery capacity indicator (Fig. 11 / item
7)
Press the battery capacity indicator switch (8).
The battery capacity indicator (7) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
- 12 -
06.04.2022 13:53:32 06.04.2022 13:53:32