Using Headphones; Dab Radio Mode - Sharp XL-B520D Manual Del Usuario

5
20.
Shuffle: In CD/USB mode: Shuffle songs on/off.
21.
In CD mode: Press to program the playback order.
22. In CD mode: Press once to play the first 10 seconds of every
track on a CD. Press again for the current track to play in full.
23. Bass +/-: Press to adjust the bass.
24. Volume +/-: Press to adjust the volume.
25. Treble +/-: Press to adjust the treble.
26. Numeric keypad (0-9): Used for song/preset selection, or to enter a
frequency.
27. Alarm: Press to set up Alarm 1/2.
When in standby, press to switch on/off alarms.
28. Sleep timer: Press to cycle through sleep timer options.
Using your DAB+/FM hi-fi micro system
Connection
NOTE: Your micro system has been supplied with a power
adapter. Please check and ensure that you connect the correct
3 pin or 2 pin part to the power adapter that is appropriate
for the country where the product will be used.
Connect the aerial to the back of the micro system to receive the best
possible radio reception and signal quality.
Connect the right and left speaker cables to the RCA sockets on the back
of the main unit.
Connect the power adapter lead to the power input on the back of
the micro system and plug the power adapter into the wall socket
and switch on. The micro system will power on and display <SHARP
sharpconsumer.eu> and then go into standby.
NOTE: The processes described here use the controls on the
main unit (unless specified). For controls using the remote
control, please refer to the 'Remote control' section.
Initial set-up
Extend the aerial to ensure the maximum signal strength when you scan
for radio stations.
Short press to switch on your micro system. It will begin an
automatic scan for DAB stations. A progress bar will show the progress of
the scan and the number of stations found.
When the scan is complete your micro system will select the first
available station and begin to play. By default, stations are listed
numerically and then alphabetically.
NOTE: The DAB radio station list is stored in the memory; the next time
the micro system is switched on, the station search does not take place.
Short press or to scroll through the available stations. To select
the station displayed, short press
your micro system tunes to your selected station.
Time and date
Time and date will be synchronised automatically to that broadcast by
the DAB service in 24-hour format.
To set the time and date manually, turn on the radio. Long press
enter the menu options.
to select <System> / <Time> / <Set Time/Date>. <Set
Use
time> is displayed and the hour digits will flash; use
hours and minutes. <Set date> is displayed and the day will flash; use
to set day, month and year. <Time Saved> is shown once the
year is confirmed and you will return to the <Set Time/Date> menu.
Use to change the clock/date format and auto update settings.
Long press to exit the menu.
. There will be a short delay whilst
to set
Change the mode
Short press to change between <DAB+>, <FM>, <Bluetooth>,
<CD>, <USB>, and <Aux in>. modes. The display screen will confirm
the mode.
Equaliser (EQ) settings
You can adjust the sound of the micro system using the equaliser presets.
Press and hold . Use
Select the EQ option of your choice: <Flat>, <Classic>, <Jazz>, <Pop>,
<Rock>, <Voice>, <Movie>, <Music>, <Dance>, <Sport>, and
<My EQ...>.
Long press to exit the menu.

Using headphones

You can connect headphones with a 3.5mm jack (not included) to the
headphone jack. When you have them connected, sound will be heard
via the headphones only.
NOTE: Always keep the volume within reasonable limits.

DAB Radio mode

Select DAB radio mode
Short press until the screen displays <DAB+>. The first time you
use the micro system or if the station list is empty, your micro system will
automatically begin to scan for DAB radio stations. A progress bar will
show the progress of the scan and the number of stations found during
the scan will also be displayed. If you were listening to a DAB station
when you switched the micro system off, this station will automatically
be selected when you switch the micro system back on.
Changing DAB stations
Use and to scroll through the available stations. Press
select when the station you want to listen to is displayed. There will be a
short delay whilst your radio tunes to your selected station.
Scanning for DAB stations
With DAB radio, additional stations and services regularly become
available. Carry out a manual scan periodically to make sure that you
have the most up-to-date station listing stored within the memory of
your micro system.
In DAB mode:
Long press . Use
display will change to <Scanning...>. A progress bar will show the
progress of the scan and the number of stations found.
Prune DAB stations
You can remove the DAB stations in the station list that cannot be
received in your area. These are listed with a <?> prefix.
In DAB mode:
Long press . Use
to
<No> Yes> is displayed. Use
with a <?> prefix will now no longer be displayed.
Storing a DAB station preset
Your micro system can store up to 20 DAB radio stations in its preset
memories for instant access to your favourite stations.
NOTE: Storing DAB radio station presets do not overwrite FM station presets.
Tune the micro system to the DAB radio station that you wish to preset.
Long press until <Preset Store <1:(Empty)>> is displayed. Use
to move to the preset location that you would like to store the radio
station to (1-20). Press
to scroll to <System> / <Equaliser>.
to scroll and select <Full Scan>. The
to scroll and select <Prune>. <Prune?
to scroll and select <Yes>. Stations
to select. The display will confirm <Preset X
to