Mounting And Operation; For Your Safety - Bosch EasyAquatak 100 Manual Original

– Uncertainty K

Mounting and Operation

Representation/Action Ob-
jective
Delivery scope EasyAquatak
100
Delivery scope EasyAquatak
110/120
Mounting cable bracket/in use
storage for gun
Connecting/disconnecting high
pressure gun to lance
Connecting/disconnecting
nozzle
Connecting/releasing pressur-
ised water/disconnecting high
pressure water supply hose
Connecting to the water supply
Switching On
Switching Off
Attaching Nozzle
Adjust water jet
Connect detergent bottle
Clean nozzle
Clean both filters
Transport
Storage
Selecting accessories
Switching on

For Your Safety

Warning: Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). If in doubt contact a quali-
fied electrician or the nearest Bosch Service Centre.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 2.5 mm – max length 25 m
Note: If an extension cable is used it must be earthed and
connected through the plug to the earth cable of your supply
network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest
Bosch Service Centre.
Bosch Power Tools
3 600 HA7 E..
2
m/s
Figure Page
ded for outdoor use.
The connections (plugs and sockets) should be kept dry and
A 216
off the ground.
For increased electrical safety use a Residual Current Device
B 217
(RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
C 218
If the supply cord is damaged, it must be replaced by a
Bosch Service Centre.
D 218
For products not sold in GB:
Warning: For your safety, it is required that the plug at-
tached to the product is connected with the extension cord.
D 218
The coupling of the extension cord must be protected
against splash water, be made of rubber or coated with rub-
E 219
ber. The extension cord must be used with a cable strain re-
lief.
To prevent damage to the appliance, do not allow it to oper-
F 219
ate dry.
G 220
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
H 220
plug with internal fuse (ASTA approved to BS 1362).
I − J 221 − 222
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
K 223 thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
L 224
The severed plug must be disposed of to avoid a possible
M 224
shock hazard and should never be inserted into a mains
N 225
socket elsewhere.
O 225
Operation
P 226
To prevent damage to the appliance, do not allow it to op-
u
erate dry.
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and wa-
ter supply hose. Release trigger. Press the safety lock (front
button on the gun handle).
Turn button on main switch. Point the power gun down-
wards. Press the trigger safety lock to release the trigger.
Fully press the trigger.
3 600 HA7 F..
0.7 1.5
WARNING: Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and inten-
F 016 L94 123 | (22.11.2022)
English | 13
3 600 HA7 9..
0.6