After-Sales Service And Application Service - Bosch Indego S 500 Manual Original

Ocultar thumbs Ver también para Indego S 500:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
28 | English
Problem
Possible Cause
Mower does not ap-
LogiCut system depends on the garden
pear to cut logically
conditions. Mower does not necessarily
have to continue in the next uncut area.
Mower does not always go in a straight line
when travelling between areas
Mower frequently does not find right posi-
tion or turns on the spot
Wire crossed while marking an object
Mower runs in random paths in an addi-
tional lawn without docking station.
Perimeter wire keeps
Wire is not taut between pegs
being cut
Distance between pegs is more than 75 cm
Mower leaves ragged
The mower does not mow often enough
finish/poor quality of
cut
Cutting blades blunt
Possible clogging
Perimeter wire not
No power at the docking station
detected
Perimeter wire damaged/cut
Wrong installation (e.g. not enough dis-
tance between wires)
Perimeter wire close to a source of interfer-
ence
Height-of-cut button
Possible clogging
stuck
After-sales Service and Application
Service
www.bosch-garden.com
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the mower.
It is possible, that the software version of your mower is re-
quired (see „Menu > Settings > Info").
If the mower is requested to be sent to the service centre,
the mower and docking station must always be sent to-
gether. Do not remove the battery.
Before sending in, remove any personalised top cover that
may have been fitted and any accessory cover.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
F 016 L94 038 | (06.10.2022)
Corrective Measure
Further information can be found on the Installation
Guide.
If behaviour re-occurs often, remap garden.
No corrective action needed.
Change wire ID.
Follow instructions in the Installation Guide.
Normal behaviour. The LogiCut system only works in
areas with docking station.
Make wire taut and ensure distance between pegs is
maximum 75 cm. Follow instructions in the Installation
Guide. Use the wire connectors to repair the cut.
Mow more frequently for a good result (e.g. by means of
more/longer slots in schedule).
Reverse or replace cutting blades (see figure J).
Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
Check if the docking station is powered up (LED is on).
Check perimeter wire for damage.
Follow instructions in the Installation Guide.
Remove any excess (e.g. coiled up) perimeter wire
around the docking station. Change perimeter wire ID in
the menu.
Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Bosch Power Tools

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Indego s+ 500Indego m 7003600hb023600hb03

Tabla de contenido