Peg-Perego Booklet Manual Del Usuario página 16

_ WARNING Don't use the rain cover (if present)
on a product without a hood or parasol that can
hold it. Always use the rain cover only under adult
supervision. Don't use the rain cover indoors and
check to ensure the child is not to warm; do not
park the vehicle close to heat sources and keep well
away from the lighted cigarettes. Ensure that the rain
cover is not interfering with any moving parts of the
carriage/stroller. Always remove the rain cover before
folding your carriage/stroller.
_ WARNING This product is not suitable for running or
skating.
_ Always apply the brake when loading or unloading
children.
_ WARNING Do not add any mattress are not approved
by the manufacturer.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if you have
any complaints please contact the Assistance Service.
_ Booklet: basket; 2 back wheels with brake lock, back
wheel axis, 2 front wheels, handlebar, hood, front bar.
INSTRUCTIONS
1 OPENING: Before opening the frame, remove (without
using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER BEYOND ITS
LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY HANDLE OR
TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES TO THIS
FEATURE.
Press down the side fastener, hold the upper section of
the handle and rotate it towards you until the frame is fully
opened (fig_a). Open frame (fig_b).
The frame is properly opened when the attachment on the
base clicks into place, as shown.
2 FITTING THE WHEELS: Slot the uprights into the rear
wheel crosspiece (fig_a), ensuring that it is facing the
right way, then push the rear wheels on and make
sure that they click into place (fig_b). To mount the
front wheels, fit them into the uprights until they lock into
place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle tube
faces upwards, align it with the stroller (Fig_a).
Fasten the handle to the frame as shown in the figure
(Fig_b).
To complete the operation, press the two side buttons
on the handle (Fig_c) to ensure the handle pushes in
all the way, until it clicks into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket tube to
the horizontal position. Press the silver buttons under
the metal basket tube located at the back of the stroller
(fig_a) and remove the metal tube (fig_b). Thread the tube
through the fabric loop on the back of the basket, making
sure that the two silver buttons are facing downward
(fig_c). Re-attach the tube to the housings (fig_d).
5 Secure the two upper basket vinyl eyelets to the two grey
buttons on either side of the metal tube housing. (fig_e).
Remove the cardboard from the lower rear bar.
IMPORTANT! Secure the two lower basket vinyl eyelets
to the two grey buttons on the top of the lower rear bar.
Please note that the eyelets open (fig_f).
WARNING! If this operation is not performed correctly,
the basket will not properly hold the weight.
Attach the basket tabs to the grey buttons on the front of
the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS VIDEO AT:
WWW.PEGPEREGO.COM
6 Attach the back of the hood with Velcro (fig_a), slide
the hood attachments into their slots (fig_b), fasten
the elastic straps to the buttons placed inside the
handle (fig_c), and button the sides of the hood to
the frame (fig_d).
7 FRONT BAR: insert the front bar until it click into place
(fig_a). To remove the front bar, press the buttons on
both sides and pull it out (fig_b). WARNING: the front
bar is not designed to support a child's weight; the
front bar is not designed to lift the seat with the child
seated inside. The front bar is not a replacement for
the safety harness.
8 FIXED OR SWIVELING FRONT WHEELS: Lift the levers
to prevent the wheels from swiveling (fig_a) and
lower them to allow the wheels to swivel (fig_b). On
uneven surfaces, the wheels should be set to their
fixed position.
9 BRAKE: Press the lever down to apply the brake on the
chassis and lift it to release the brake.
10 ADJUSTABLE HANDLEBAR: To adjust the height of the
handlebar, press both of the side buttons at the same
time (fig_a) and swing it into the desired position
(fig_b), then release the buttons.
11 FOOTREST: before adjusting the foot rest, ensure its
cover is accurately fitted; if it isn't, fit it accordingly. To
lower the footrest push the two levers downwards and
then push the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
12 HOOD: the hood has an eyelet from which to hang
the baby's favourite toy (fig_a). You can unfasten the
Velcro strap and roll up the back of the hood, fixing
it up with the elastic, for increased ventilation when
using the stroller with the backrest lowered (fig_b).
13 ADJUSTING THE BACKREST: to lower the backrest,
press the clip and the backrest will move down to the
desired position.
To raise the backrest, press the clip and lift the
backrest to the desired height.
14 FIVE POINT SAFETY HARNESS: to fasten it, push the two
waist strap buckles (with the shoulder straps attached
– arrow_a) into the leg divider until they click into
place (arrow_b). To unfasten it, press the round button
in the centre of the buckle (arrow_c) and pull the waist
straps out (arrow_d).
15 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, move it
in the opposite direction.
To adjust the height, slip the belts through the eyelet
in the fabric (fig_b) and position them in the most
suitable eyelet.
16 FOLDING UP: to fold the stroller, it is best to set the
front wheels to their fixed position and close the
hood (if fitted). Place the handle as shown in the figure
(fig_a).
Pull the inside handle on the base (fig_b) and lift it (fig_c);
the handle will drop forward until the frame is closed.
17 To close correctly, check the side hook is inserted
(fig_a). If not automatically locked, compress the
chassis slightly. When folded, the stroller will free
standing (fig_b).
18 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull the pivot outwards and
remove the wheel as shown in the figure (fig_a).
To remove the front wheels: press the tab as shown, and
remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
19 REMOVABLE ITEMS: to remove the hood, take the
elastic off from the buttons on the inside of the
handlebar (fig_a), detach the press studs the sides of
the chassis (fig_b), detach the Velcro strip from the
backrest (fig_c) and remove the attachments of the
hood from their positions on the chassis (fig_d).
20 To remove the seat fabric, press in the holes on the
inside of the chassis (fig_a); remove, from the side of
the seat, the rigid flap of the chassis fabric ((fig_b),
unfasten the elastic of the net from the side buttons
inside the handlebar (fig_c) and unfasten the elastics
from the buttons inside the chassis (fig_d).
21 From the front, remove the lining from the foot
platform (fig_a), remove the leg divider strap from
under the seat (fig_b), unbutton the seat fabric (fig_c),
- 16 -