Fein AKFH18-5 AS Serie Manual Del Usuario página 29

Character
L
wA
L
pCpeak
K...
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
hand-guided bevel milling machine for professional use
by instructed operating personnel in weather-pro-
tected environments using the application tools and
accessories recommended by FEIN:
– for machining workpieces made of steel, cast steel,
fine-grained steel, stainless steel, aluminium, alumin-
ium alloys, brass and plastic
– for commercial use in industry and trade
– for the preparation of K-, V-, X- and Y-shaped
welding joints
– for machining visible edges in plant, equipment and
general engineering
– for rounding edges for optimal paint preparation or
as impact protection
Special safety instructions.
Fasten and secure the workpiece with screw clamps or
other suitable clamps to a stable surface. When hold-
ing the workpiece manually it is unstable and can lead
to loss of control and injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
Do not use a damaged accessory. Before each use,
check the indexable inserts for chipping and cracks,
wear or heavy use. If the machine or application tool is
dropped, inspect for damage or install an undamaged
application tool.
Unit of measurement,
international
dB
dB
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
Explanation
Sound power level
Peak sound pressure level
Uncertainty
Vibrational emission value according to EN 62841 (vector sum of
three directions)
Basic and derived units of measurement from the international sys-
tem of units SI.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye pro-
tection must be capable of stopping flying debris gener-
ated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise
may cause hearing loss.
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal pro-
tective equipment. Fragments of workpiece or of a bro-
ken accessory may fly away and cause injury beyond
immediate area of operation.
Always hold the power tool firmly when starting it. The
reaction torque of the motor, as it accelerates to full
speed, can cause the power tool to twist.
If possible, use clamps to fasten or affix the workpiece.
Never hold a workpiece in one hand and the power tool
in the other hand while in use. Clamping workpieces
allows you to use both hands for better control the
power tool.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Do not operate the power tool near flammable materi-
als. Sparks could ignite these materials.
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in elec-
trocution or shock.
Secure the work piece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
en
29