Comet Spa CPS 50 E Manual Del Usuario página 34

5.4. SQUEEGEE ASSEMBLY
Slightly screw the two knobs ( Photo M - 6 ) into the
squeegee body and insert the squeegee into the slots
situated on the squeegee support.
Screw the two knobs ( Photo M - 6 ) in order to secure
the squeegee to the support.
Firmly insert the suction hose ( Photo M - 3 ) into the
pipe in the squeegee body.
5.5. SQUEEGEE DISASSEMBLY
Disconnect the suction hose from the squeegee body.
Unscrew the two knobs ( Photo M - 6 ) that secure the
squeegee to its support and pull the squeegee to free it.
5.6. SQUEEGEE BLADES DISASSEMBLY /
ASSEMBLY
Disassemble the squeegee from its support (see 6.5)
Unscrew the knobs ( Photo M - 4, Photo M - 6 ) placed
on the squeegee body and apply some pressure on
their bolts in order to push out the plastic support of
the squeegee blades from the squeegee body.
Tear off the rubber blades from the plastic support.
Assemble the new blades on the plastic support by
the means of the plastic pins that have to be fixed in
the holes placed the blades.
Push the plastic support of the squeegee blades into
the squeegee body and screw the knobs ( Photo M - 4,
Photo M - 6 ) to secure it to the squeegee body.
Reassemble the squeegee to its support (see 6.4).
5.7. SQUEEGEE ADJUSTMENT
The knob screw on the squeegee support ( Photo M
- 7) adjusts the squeegee's inclination with respect to
the floor. The two red knobs on the sides, connected
to the rear wheels of the squeegee ( Photo M - 2 ) are
to adjust the pressure of the squeegee to the floor.
When the squeegee is perfectly adjusted, the rear
squeegee blade, sliding as it moves, bends in all
points forming an angle of 45° with the floor.
As the machine operates (advances), the knobs ( Photo
M - 2, Photo M - 7 ) can be used to adjust the inclination
and pressure of the squeegee blades on the floor.
Squeegee drying must be uniform along the entire
drying line: damp patches mean that drying is insuffi-
cient; turn the adjustment knobs to optimize drying.
5.8. SPLASH GUARD ASSEMBLY/
DISASSEMBLY
The splash guard is attached to the brush plate by in-
terlocking on the plastic cover.
To remove the splash guard is sufficient to pull it
down until it detaches from the plastic cover.
To replace the splash guard,push it into the bottom
edge of the plastic cover from one end and continue
pushing up to the other end.
5.9. BRUSH ASSEMBLY / DISASSEMBLY
• Never use the machine if the brush or the pad
holder with abrasive pad is not perfectly installed.
Assembly:
Make sure that the brush plate is raised; otherwise lift
it by following the instructions provided in the spe-
cific section.
Make sure that the ignition key on the control panel
is in OFF position.
Place the brush under the plate, taking care that the
coupling flange on the brush is under the metal cou-
pling of the machine.
Lower the brush plate and start the brush rotation
operating the brush motor switch and the brush op-
eration lever; the brush will couple automatically.
To assemble the pad holder follow the same procedure.
• Do not allow the length of the rows of brushes to
become lower than 1 cm.
• Do not allow the thickness of the abrasive disks to
become less than 1 cm.
Working with excessively worn brushes or excessively thin
abrasive disks may damage the machine and the floor.
Regularly check the wear on these parts before start-
ing to work.
Disassembly or replacement:
Make sure that the brush plate is raised; otherwise lift
it by following the instructions provided in the spe-
cific section.
Make sure that the ignition key on the control panel is
in position OFF position.
While holding the brush with the hands under the
plate, turn it in the rotation direction while lowering
to release it from the metal coupling on the machine.
To disassemble the pad holder follow the same pro-
cedure.
5.10. FILLING AND DRAINING THE SOLUTION
TANK
• The temperature of the water or the detergent
should never exceed 50°C.
☞ Always empty the recovery tank ( Photo N - 4) be-
fore filling the solution tank ( Photo N - 3).
To fill the tank:
- Pour into the tank the required quantity of the
chemical product, considering the percentage indi-
cated by the supplier, with reference to the full tank
capacity listed on the product sheet.
• Use only those products suitable for the floor and
the dirt to be removed.
- Pour water in the filling opening placed in the front
of the machine ( Photo H - 2, Photo N - 2 ).
Leave 2 cm between the filling opening and the liquid
level. Do not fill beyond this point!
34