Comet Spa CPS 50 E Manual Del Usuario página 36

- Switch ON the suction motor switch ( Photo A - 3).
- Lower the squeegee unit by using the lift/lower lever
( Photo B - 3)
- Lower the brush plate unit by using the lift/lower
lever ( Photo B - 2)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo B - 4); releasing the lever
the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
Model DC 24V
- Verify that the battery connector placed in the back
of the machine ( Photo D - 7) is connected.
- Put the ignition key ( Photo D - 1) in and turn ON
the machine.
- In the control panel, check the battery charge status
( Photo C - 3 )
- Switch ON the brush motor switch ( Photo C - 1).
( ! ) The brush will start the rotation only when the
machine operator will operate the brush operation
lever ( Photo D - 2).
- Switch ON the suction motor switch ( Photo C - 2).
- Lower the squeegee unit by using the lift/lower lever
( Photo D - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo D - 3)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo D - 2); releasing the
lever the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
Model DC 24V with traction
- Verify that the battery connector placed in the back
of the machine ( Photo F - 8) is connected.
- Put the ignition key ( Photo F - 1) in and turn ON the
machine.
- In the control panel, check the battery charge sta-
tus ( Photo E - 1 ) and, if sufficient, select the running
speed wished ( Photo E - 3, E - 4 ).
- Switch ON the brush motor switch ( Photo E - 5).
• The brush will start the rotation only when the
machine operator will operate the brush opera-
tion lever ( Photo F - 2).
- Switch ON the suction motor switch ( Photo E - 6).
- Lower the squeegee unit by using the lift/lower lever
( Photo F - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo F - 3)
- Wash the floor moving forward by pulling the trac-
tion lever ( Photo F - 2) up or push the traction lever
down to reverse traction; releasing the lever the trac-
tion will stop immediately and brush rotation will
stop after few seconds.
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
5.14. WORK METHOD
5.14.1. PREPARATION AND WARNINGS
Remove any loose solid residue from the surface to be
treated (using suitable tools, such as vacuum clean-
ers, sweepers, etc.). It this is not done, the solid dirt
might prevent the squeegee from operating correctly,
reducing drying efficiency.
Only trained personnel can drive this machine.
5.14.2. BATTERY CHARGE LEVEL CONTROLS
The sequence of lights of the battery charge control
( Photo C - 3, E - 1 ) progressively turns off until the
battery is discharged . When the red light turns on (
Photo C - 3C, E - 1C ), turn off the brush motor, close
the detergent solution outlet, finish drying the small
residual moisture and go to the battery charging area
to charge the battery.
( ! ) The batteries may be irreparably damaged if the
residual charge level drops too low (see the battery
operating manual). Do not force the battery discharge
beyond the safety limits, turning the key off and on or
in any other manner.
5.14.3. DIRECT SCRUBBING OR FOR SLIGHTLY
DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and use
it as described in paragraph 6.13.
☞ Never use the machine without the detergent solu-
tion: the floor might be damaged.
5.14.4. INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 6.13, with-
out drying the floor
Allow the detergent solution to work on the dirty
floor according to what is indicated in the information
relative to the detergent used.
Second set of operations:
Proceed as explained in the previous "Direct Washing"
paragraph (6.14.3) to also proceed with drying the floor.
• Never use the machine without the detergent solu-
tion: the floor might be damaged.
5.14.5. POST-SCRUBBING OPERATIONS
Close the detergent solution outlet.
Lift the brush unit and turn off the brush motor.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
36