YATO YT-82810 Manual De Instrucciones página 18

EN
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains.
In addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (II), the more LEDs will light up, the more
fully the battery pack is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (II).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
Circular saws
Select the circular saw, which is assigned for cutting the selected type of material. The more teeth has saw the smoother will be
the edges of the cut. Saws, which are having dozens of teeth, are better suited for cutting thinner material, of a thickness of less
than 1 cm and for soft wood.
Attention! Do not cut other materials than those mentioned in the manual.
You should check whether the blade is not damaged, cracked, whether the cutting teeth are not broken, etc. In the case of dam-
age, replace the circular saw for a new one.
Do not use saw blades which are deformed or cracked!
Do not use saw blades made of high speed cutting steel!
Do not use abrasive discs!
Do not use saw blades which do not comply with the technical data specifi ed in this manual!
Do not use saw blades, which body is thicker than the thickness of the splitting wedge!
You should not use saw blades of a maximum acceptable rotational speed less than the rotational speed of the saw.
Mounting and replacing of the saw blade (II)
Attention! During exchange or mounting of the saw blade you should do not disassemble saw guards!
You should lock the blade rotation and loosen the screw that secures the blade.
Remove the mounting fl ange and circular saw from the saw spindle.
Clean the spindle, the fi xing fl anges and the inside part of the covers of the dust and debris, which can be remaining after work.
Install the mounting fl ange, and then install a new blade on the spindle.
Install the external mounting fl ange, and then, by blocking ability of the saw blade to rotate, tighten the screw, which is fi xing the saw.
Adjustment of the cutting depth (III)
If necessary, the tool allows you to adjust the depth of cut, it is easier due to application of the guide with scale (placed on the
back of the tool). To do this, you should, by using the screw, loosen the lock, which is placed on the guide with scale, then set the
desired cutting depth and lock the screw.
Adjusting the cutting angle (IV)
The tool allows for cutting planes on angle ranging from 0 to 45 . To do this, you should set the desired angle on scale placed on
O
the front of the tool and tighten fi rmly and securely the locking screw.
O R I G I N A L I N S T R U C T I O N S
18