Nemox GELATO 5+5K TWIN CREA i-Green Instrucciones Para El Uso página 11

SWITCHING FROM AUTOMATIC TO MANUAL OPERATION
During the processing program, it is possible to switch to manual mode at any time.
Holding down button (11) for 3 seconds switches the machine to manual mode while enabling the paddle LEDs (2a) and
compressor (1a).
The storage cycle selected will be deactivated.
TURNING OFF THE MACHINE DURING AUTOMATIC OPERATION MODE
If you need to turn off the machine before the completion of the active processing program, you first need to switch to
manual mode by pressing and holding button (11) for 3 seconds and then pressing paddle (2) and compressor (1) to stop
any activity. Do not act directly on the main switch (10)!
STORAGE CYCLE VARIATION WHILE A PROGRAM IS RUNNING
During the preparation phase it is possible to automatically vary the storage cycle set at any time. Repeatedly press
button (12) until the LED that corresponds to the desired cycle is activated. The LED will flash for 3 seconds and
becomes steadily lit: the new storage cycle is selected at this point and will be performed at the end of the program. Each
preparation program will activate at the end of the selected storage cycle.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops paddle (5) and does not affect the preparation program.
The closure of the lid (3) starts the motion of the paddle (5) (where, at that time it is provided by the selected program). If
the mixture proves excessively thick to prevent the movement of the paddle, the machine will automatically activate the
previously selected storage cycle.
AUTOMATIC STORAGE
There are 4 storage cycles available for every whipping program (total of 16 cycles) devised to meet a wide range of
needs.
• In automatic mode, if the machine is not stopped, at the end of each production cycle is enabled the gelato storage
cycle selected.
• The activation of the storage function is indicated by flashing of the LED corresponding to the processing program of
the gelato selected.
• The desired cycle selection can take place either at the beginning or during the processing phase.
• Depending on the type of recipe and/or the quantity prepared, every set of storage cycles enables keeping gelato,
Granita and sorbet or other whipped products at the desired conditions.
• Pressing the button (12) several times causes the selection LEDs of the various storage cycles to light up in sequence.
If you switch from the first (LED (12a) active) to the fourth (LED (12d) active) storage program, the density of gelato
increases gradually.
• Once you have selected the desired cycle, the corresponding LED will flash for 3 seconds and will become steadily lit,
enabling the selection.
VARIATION OF THE STORAGE CYCLE
It is always possible select a different storage cycle (relating to the same production program), during the active phase
and during the pause phase of the cycle in progress. Repeatedly press the button (12) until the LED corresponding to
the desired cycle is activated. The LED will flash for 3 seconds and will become stable: the new storage cycle is now
selected and will be performed with its own execution times. Should it be necessary to pass to a series of storage cycles
specific to a different program from the one selected, it is necessary to activate the corresponding program first by
pressing the key (11). Once the program has been activated, go to the storage function by pressing buttons (2) and (1)
simultaneously for 3 seconds. The machine will activate the series of storage cycles relating to the selected program.
SWITCHING FROM STORAGE PHASE TO A PRODUCTION PROGRAM
With the storage active, you can activate an automatic program simply by selecting it by pressing button (11). The LED
corresponding to the selected program will flash for 3 seconds and become steadily lit; the machine will exit the storage
cycle and run the selected program.
Subsequently, the storage cycles associated to the selected program will be enabled.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops the paddle (5) and does not affect the storage cycle.
The closure of the lid (3) enables the paddle operation (5) (on the condition that it is provided by the selected storage
cycle in that moment). If the mixture proves excessively hard and prevents the movement of the paddle, the machine will
English
11