Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS: For optimal performance and
operation, read these instructions carefully before installing
your new pump. This manual provides valuable guidance and
instructions that should be followed to perform installation,
operation and maintenance procedures for this product. It
should be kept near the installation for immediate reference.
Record nameplate data from your new pump on the blank
template located in "Maintenance" on for future reference.
This is the safety alert symbol. When you see this symbol
on your pump or in this manual, look for one of the following
signal words and be alert to the potential for personal injury.
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if ignored.
warns about hazards that will or can cause minor
personal injury or property damage if ignored.
The word NOTE indicates special instructions that are important
but not related to hazards.
The hazards stated in this manual are not all-inclusive. To
minimize the risk of hazard, it is strongly recommended that
installation, operation and maintenance be performed by a
qualified professional in accordance with local codes and
standards for safe operation.
CALIFORNIA PROPOSITION 65 WARNING
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
ELECTRICAL SAFETY
RISK OF ELECTRIC SHOCK Can shock, burn or kill
All wiring should be done by a qualified electrician.
Wire motor for correct voltage. See "Installation" section of
this manual and motor nameplate.
Ground motor before connecting to power supply.
Follow wiring instructions in this manual when connecting
motor to power lines.
A complete power disconnect switch must be incorporated
in the fixed wiring.
Install, ground, wire and maintain your pump in compliance
with all applicable national and local codes and ordinances.
Consult your local building inspector for code information.
P15008 (04-15-2023)
GENERAL SAFETY
RISK OF EXPLOSION. The pump body may explode
if used to boost pressure above the pressures noted on.
Do not use this pump with inlet pressure greater than 70 psi
(483 kPa) or less than 3 psi (20.7 kPa). If not already in the piping
system, install a pressure relief valve in the pump discharge
line capable of passing the full pump flow at maximum rated
pressure. If local code requires installation of a pressure relief
valve capable of handling the full pump flow at a pressure less
than 100 psi (689 kPa), follow the code requirements.
RISK OF FIRE OR EXPLOSION. To avoid risk of fire
and explosion, pump water only with this pump. Do not pump salt
water, flammable liquids or chemicals. Do not use the pump near
gas pilot lights or where chemical or gas fumes are present.
Use of an electric pump with liquids other than water or in an
atmosphere containing chemical or gas fumes may ignite those
liquids or gases and cause injury or death due to an explosion
and/or fire. Pump approved liquids only with this pump.
RISK OF BURNS. If water is trapped in the pump
during operation it may turn to steam. Trapped steam may cause
an explosion resulting in injury or property damage. Never run
the pump with the outlet closed or obstructed.
RISK OF FREEZING. Do not allow pump, piping,
or any other system component containing water to freeze.
Freezing may damage system, leading to injury or flooding.
Allowing pump or system components to freeze will void the
warranty.
NOTE: Only service agent or qualified person should replace
power cord to avoid injury.
Periodically inspect pump and system components.
Wear safety glasses at all times when working on pumps.
Keep work area clean, uncluttered and properly lighted; store
properly all unused tools and equipment.
ORDERING REPLACEMENT PARTS
Locate the Pentair nameplate on pump. This plate is normally on
the pump case or bracket (seal plate).
To ensure receipt of correct parts, provide all nameplate data
when ordering. Catalog number is most important to reference.
Write the nameplate information below, as nameplates can
become worn or lost.
Model:
S.N. or Date:
Impeller Dia.:
Catalog No.:
3
Publicidad
