Bosch Professional GBH 2-24 RE Manual Original página 14

OBJ_BUCH-2460-001.book Page 14 Thursday, May 7, 2015 10:48 AM
14 | English
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause hear-
ing loss.
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Hold the tool by the insulated gripping surfaces when
performing operations where the application tool or
the screw could contact hidden wiring or its own power
cord. Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the operator.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
GBH 2-24 RE
The machine is intended for hammer drilling in concrete, brick
and stone. It is also suitable for drilling without impact in wood,
metal, ceramic and plastic. Machines with electronic control
and right/left rotation are also suitable for screwdriving.
1 609 92A 170 | (7.5.15)
GBH 2-24 DRE/DFR
The machine is intended for hammer drilling in concrete,
brick and stone, as well as for light chiselling work. It is also
suitable for drilling without impact in wood, metal, ceramic
and plastic. Machines with electronic control and right/left ro-
tation are also suitable for screwdriving.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Quick change keyless chuck (GBH 2-24 DFR)
2 SDS-plus quick change chuck (GBH 2-24 DFR)
3 SDS-plus tool holder
4 Dust protection cap
5 Locking sleeve
6 Lock ring for rapid-change chuck (GBH 2-24 DFR)
7 Rotational direction switch
8 Lock-on button for On/Off switch
9 On/Off switch
10 Release button for mode selector switch
(GBH 2-24 DRE/DFR)
11 Mode selector switch (GBH 2-24 DRE/DFR)
12 Button for depth stop adjustment
13 Depth stop
14 Auxiliary handle (insulated gripping surface)
15 Release button for drilling/hammer drilling selector
switch (GBH 2-24 RE)
16 Selector switch for drilling/hammer drilling
(GBH 2-24 RE)
17 Handle (insulated gripping surface)
18 Securing screw for key type drill chuck*
19 Key type drill chuck*
20 SDS-plus adapter shank for drill chuck*
21 Drill chuck mounting (GBH 2-24 DFR)
22 Front sleeve of the quick change keyless chuck
(GBH 2-24 DFR)
23 Retaining ring of the quick change keyless chuck
(GBH 2-24 DFR)
24 Extraction sleeve of the dust extraction attachment*
25 Clamping screw for the dust extraction attachment*
26 Depth stop of the dust extraction attachment*
27 Telescopic pipe of the dust extraction attachment*
28 Wing bolt of the dust extraction attachment*
29 Guide pipe of the dust extraction attachment*
30 Universal bit holder with SDS-plus shank*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Bosch Power Tools