Tabla De Contenido; Table Of Contents - skilsaw SPT62MTC Instrucciones De Funcionamiento Y Seguridad

1609B00427 eng.qxp_SPT62MTC 5/12/15 1:53 PM Page 6
personal injury.
Double Insulated Tools
Double insulation
electric power tools which eliminates the need for
the three wire grounded power cord and grounded
power supply system. It is a recognized and ap-
proved system by Underwriter's Laboratories, CSA
and Federal OSHA authorities.
• Servicing of a tool with double insulation requires
care and knowledge of the system and should be
performed only by a qualified service technician.
• WHEN SERVICING, USE ONLY IDENTICAL RE-
PLACEMENT PARTS.
• POLARIZED PLUGS. To reduce the risk of elec-
trical shock, your tool is equipped with a polarized
plug (one blade is wider than the other), this plug
will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to in-
stall the proper outlet. To reduce the risk of elec-
trical shock, do not change the plug in any way.
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
General Safety Rules For Bench Top Tools .2-3
Safety Rules For Saws . . . . . . . . . . . . . . . . .3-4
Table of Contents . . . . . . . . . . . . . . . . . . . .6
Electrical Requirements . . . . . . . . . . . . . . .7
Recommended cutting capacity . . . . . . . . . .7
Getting To Know Your Saw . . . . . . . . . . . .8-9
Unpacking and Checking Contents . . . . .10
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Removing and installing Blades . . . . . . . . . .10-11
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . .12
Miter Scale Pointer Adjustment . . . . . . . . . . .12
Transporting and Mounting . . . . . . . . . . .13-14
Preparing to Lift the Saw . . . . . . . . . . . . . . . .13
READ ALL INSTRUCTIONS - Failure to follow the SAFETY RULES identified by
BULLET (•) symbol listed BELOW and other safety precautions, may result in serious
is a design concept used in
"SAVE THESE INSTRUCTIONS"

Table of Contents

Safety
Extension Cords
• Replace damaged cords immediately. Use of
damaged cords can shock, burn or electrocute.
• If an extension cord is necessary, a cord with ade-
quate size conductors should be used to prevent ex-
cessive voltage drop, loss of power or overheating.
The table shows the correct size to use, depending
on cord length and nameplate amperage rating of
tool. If in doubt, use the next heavier gauge. Always
use U.L. and CSA listed extension cords.
RECOMMENDED SIZES OF EXTENSION CORDS
Cord Size in A.W.G.
Tool's
Ampere
Cord Length in Feet
Rating
25 50
3-6 18 16
6-8 18 16
8-10 18 16
10-12 16 16
NOTE: The smaller the gauge number, the heavier
12-16 14 12
the cord.
Permanent Attachment to Workbench . . . . .14
Temporary Mounting Using Clamps . . . . . . .14
Basic Saw Operations . . . . . . . . . . . . . . .15-17
Switch Activation . . . . . . . . . . . . . . . . . . . .15
Body and Hand Position . . . . . . . . . . . . . .15
Workpiece Support . . . . . . . . . . . . . . . . . . .16
Using Workpiece . . . . . . . . . . . . . . . . . . . .16
Long Workpiece Clamp . . . . . . . . . . . . . . .16
Additional Workpiece Support . . . . . . . . . .16
Chop Cut . . . . . . . . . . . . . . . . . . . . . . . . . .17
Miter Cut . . . . . . . . . . . . . . . . . . . . . . . . . .17
Maintenance and Lubrication . . . . . . . . .18
Troubleshooting . . . . . . . . . . . . . . . . . . . .19
-6-
Wire Sizes in mm 2
Cord Length in Meters
100 150 15 30 60 120
16 14 0.75 0.75 1.5 2.5
14 12 0.75 1.0 2.5 4.0
14 12 0.75 1.0 2.5 4.0
14 12 1.0 2.5 4.0 -
- - - - - -