Before Using - Hitachi Koki C 10FCH2 Instrucciones De Seguridad Y Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
M6 × 20 Screw
Clamp lever
6mm Bolt
Holder (B)
Adjust the holder
until its bottom
surface contacts the
work bench surface.
Install the side handle
Remove the M10 bolt and install the side handle that came enclosed with
this unit.
Install the sub fence (B)
In the case of direct angle cutting and angle cutting, use the sub fence.
The sub fence (B) can be installed on the right side of the guide fence
(B). Place the attached plate (A) in the position as shown in fi gure 5-c,
insert the tip in the groove of fence (B) and simultaneously, insert fl athead
screw M6 into fence (B), sub fence (B), and plate (A), then tighten nylon
nut M6 with the included 10mm box wrench until the sub fence (B) can
smoothly rotate. Then, you can realize stable cutting of the material with
a wide back face.
Sub fence (B)
M6 Nylon nut
3.
Releasing the locking pin
When the power tool is prepared for shipping, its main parts are secured
by a locking pin.
Move the handle slightly so that the locking pin can be disengaged.
NOTE:
Lowering the handle slightly will enable you to disengage the
locking pin more easily and safely.
The lock position of the locking pin is for carrying and storage
only.
8
Move
Fig. 5-a
M10 Bolt
Fig. 5-b
M6 Flat screw
Plate (A)
Fence (B)
Fig. 5-c
Handle
4.
Installing the dust bag, holder, stopper and vises
(The holder and stopper are optional accessories.)
Attach the dust bag and vise assembly as indicated in Fig. 1 and Fig. 2.

BEFORE USING

1.
Make sure the power source is appropriate for the tool.
WARNING:
Never connect the power tool unless the available AC power source
is of the same voltage as that specifi ed on the nameplate of the
tool.
Never connect this power tool to a DC power source.
2.
Make sure the trigger switch is turned OFF.
WARNING:
If the power cord is connected to the power source with the trigger
switch turned ON the power tool will start suddenly and can cause
a serious accident.
3.
Check the saw blade for visible defects.
Confi rm that the saw blade is free of cracks or other visible damage.
4.
Confi rm that the saw blade is attached securely to the power tool.
Using the supplied 10mm box wrench, tighten the bolt on the saw blade
spindle to secure the saw blade.
For details, see Fig. 34-a, Fig. 34-b, Fig. 34-c and Fig. 34-d in the section
on "SAW BLADE MOUNTING AND DISMOUNTING".
5.
Check the lower guard for proper operation.
Lower guard is designed to protect the operator from coming into contact
with the saw blade during operation of the tool.
Always check that the lower guard moves smoothly and covers the saw
blade properly.
WARNING:
NEVER OPERATE THE POWER TOOL if the safety cover does not
function smoothly.
6.
Confi rm the position of the spindle lock before using the tool.
After installing the saw blade, confi rm that the spindle lock has been
returned to the retract position before using the power tool (see Fig. 34-b).
7.
Check the Power Receptacle.
To prevent overheating, accidental stopping or intermittent operation,
confi rm that the power cord plug fi ts properly in the electrical receptacle
and does not fall out after it is inserted. Repair or replace the receptacle
if it is faulty.
Locking pin
Fig. 6
Lower guard
Fig. 7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

C 10fce2

Tabla de contenido