Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
ENGLISH
Getting Started
Getting Started
Introduction
Introduction
This manual provides operation instructions and information required to
operate the HD Elite.
Read and become familiar with the contents of this manual prior to operating
the equipment. The owner of this equipment is solely responsible for
arranging technical training.
The HD Elite is to be operated only by qualified trained technicians.
Maintaining records of personnel trained is solely the responsibility of the
owner and management. This manual assumes the technician has already
been trained in basic balancing procedures.
Corporate Information
Hunter Engineering Company
Web: www.hunter.com
For Your Safety
For Your Safety
Hazard Definitions
Watch for these symbols:
CAUTION: Hazards or unsafe practices, which could result in
minor personal injury or product or property damage.
WARNING: Hazards or unsafe practices, which could result in
severe personal injury or death.
DANGER: Immediate hazards, which will result in severe
personal injury or death.
These symbols identify situations that could be detrimental to your safety and/
or cause equipment damage.
Important Safety Instructions - Electrical
Do not operate equipment with a damaged cord or equipment that has been
dropped or damaged until examined by a Hunter Service Representative.
If an extension cord is necessary, it must have a current rating equal to or
more than that of the equipment. Cords rated for less may overheat. Arrange
the cord so that it will not be tripped over or pulled.
Never use the cord to pull the plug from the outlet. Do not let cord hang over
any edge or contact fan blades or hot manifolds.
Verify that the electrical supply circuit and the receptacle are properly
grounded.
To reduce the risk of electrical shock, do not use on wet surfaces or expose
to rain.
To reduce the risk of electrical shock, do not use on wet surfaces or expose
to rain.
Verify the appropriate electrical supply circuit is the same voltage and
amperage ratings as marked on the equipment before operating.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage the
equipment and may result in personal injury.
When servicing the HD Elite, power must be disconnected by removing the
power cord from the electrical outlet. Ensure that the HD Elite power switch
is in the off position ("O" position) before plugging the power cord into the
electrical power outlet.
Important Safety Instructions - Operation
To reduce the risk of fire, do not operate equipment near open containers of
flammable liquids (gasoline).
Read and follow all caution and warning labels affixed to your equipment and
tools.
Misuse of this equipment can cause personal injury and shorten the life of the
equipment.
Keep all instructions permanently with the unit.
Keep all decals, labels, and notices clean and visible.
To prevent accidents and/or damage to the Balancer recommended
accessories. Use equipment only as described in this manual.
Never stand on the Balancer.
Wear non-slip safety footwear when operating the Balancer.
Keep hair, loose clothing, neckties, jewelry, fingers, and all parts of body away
from all moving parts.
ALWAYS WEAR OSHA APPROVED SAFETY GLASSES. Eyeglasses that
have only impact resistant lenses are NOT safety glasses.
Important Safety Instructions - Balancers
Keep the safety hood and its safety interlock system in good working order.
Do not place any tools, weights, or other objects on the safety hood while
operating the balancer.
Verify that the wheel is mounted properly and that the wing nut is firmly
tightened before spinning the wheel.
The safety hood must be closed before touching the green "START" button, to
spin the wheel.
Raise safety hood only after wheel has come to a complete stop. If safety
hood is raised before the spin is com-pleted, the weight values will not be
displayed.
The red "STOP" button, can be used for emergency stops.
Decal Information and Placement
Right Side View
• Decal 128-1244-2 cautions the operator that spindle rotation may occur
with foot pedal depression and to keep clear of clamping components
during shaft rotation.
• Decal gives the maximum wheel diameter and maximum wheel weight
for the HD Elite.
• EN/IEC Class 3R Laser Product Certification is shown on Decal 128-
2016-2-08. This label shows the EN/IEC standards for a Class 3R Laser
Product.
• An explanation of FDA compliance standards is shown on Decal 128-
2016-2-08. FDA performance standards compliance is shown on the
decal.
• For units with TDC Laser, FDA standards for Class 2M laser compliance
are shown on Decal 128-1155-2.
• Decal 128-381-2 warns the operator not to remove the covered of the
HD Elite because of the risk of the electrical shock and not to use below
garage floor level.
• ETL certification standards are outlined on Decal 128-1120-2. Users are
cautioned not to use the balancer below garage level. • A manufacturer's
identification is also on the rear of the balancer.
Specific Precautions/Power Source
The is intended to operate from a power source that will apply 230VAC +10% /
-15%, 1 phase, 10 amp 50/60 Hz power.
The power cable includes NEMA 20 amp plug, L6-20P, between the supply
conductors of the power cord.
The power cord supplied utilizes a twist lock connector.
A protective ground connection, through the grounding
conductor in the power cord, is essential for safe operation. Use
only a power cord that is in good condition.
For information on converting from single phase NEMA L6-20P
plug to thee phase NEMA L15-20P plug refer to Form 5350-
T, "NEMA L6-20P to NEMA L15-20P Power Plug Conversion
Instructions."
Specific Precautions/Optical Scan Laser
The Optical Scan Laser is a class 1 laser designed to measure the profile of
wheel assemblies.
The laser is not a field servicable part.
No maintenance is to be performed on the laser.
(New 3R Laser) Decal: 128-2016-2-08
Wavelength: 658nm
Laser Power for Classification: <5mW
Emission Type: CW
Divergence: 3.0 mRad
Beam Diameter: 8.5 mm at aperture
Fan Angle: 57°
The Optical Scan Laser is a Class 3R laser designed to measure the profile of
wheel assemblies
The laser is not a field servicable part.
No maintenance is to be performed on the laser.
(Original 3R Laser) Decal: 128-1785-2-08
Wavelength: 635nm
Laser Power for Classification: <5mW
Emission Type: CW
Divergence: 1.1 mRad
Beam Diameter: 6.5 mm at aperture
Laser Beam spot size at 10m: <10mm
Image 1.
Publicidad
