Hunter HD Elite Balancer Instrucciones Funcionamiento página 8

HammerHead TDC Laser Precaution (optional
equipment)
The TDC (Top Dead Center) Laser Indicator is a class 2M laser designed
to aid in applying clip-on weights. The laser is not a field serviceable or
adjustable part.
Use caution in regard to reflective materials around the laser and never look
into the laser beam.
LASER RADIATION - DO NOT STARE INTO THE BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
Viewing the laser output with magnifiers or related optical instruments within a
distance of 100mm from the laser aperture may pose an eye hazard.
Turning Power ON/OFF
Push Button Switch
The balancer is equipped with a push button power switch located on the left
side of the LCD support. Use this switch for normal shut down and restarting
procedures.
Always use the power button on the LCD support turn on/off in
order to prevent data loss.
Main Power Switch
The main power ON/OFF switch is located on the back of the balancer
cabinet.
To power the balancer "ON," press the "I" side of the ON/OFF switch. To turn
all power the balancer "OFF," press the "O" side of the ON/OFF switch.
Equipment Specifications
Only a Hunter Factory-Authorized Representative should perform installation.
This equipment contains no operator serviceable parts. All maintenance and
repairs must be referred to a qualified Hunter Service Representative.
Table 1. Equipment Specifications
Electrical
Voltage:
Amperage:
Wattage:
Air
Air Pressure Requirements:
Approximate Air Consumption:
Atmospherics
Temperature:
Relative Humidity:
Altitude:
Sound Pressure Level
Equivalent continuous A-weighted sound pressure at operator's position
does not exceed 70 dB (A).
Explanation of Symbols
These symbols may appear on the equipment.
Alternating current.
Earth ground terminal.
Protective conductor terminal.
ON / OFF (Supply) condition.
l
Risk of electrical shock.
Stand-by switch.
Not intended for connection to public
telecommunications network.
Maintenance and Calibration Maintenance and Calibration
Auto Calibration
The balancer utilizes automatic calibration procedure. Once the balancer is
calibrated at installation time, no further operator input is required.
Image 2.
Image 3.
208-240V, 3 amp, 50/60 Hz, 1 ph
(NEMA 20 amp plug, L6-20P)
10 amperes
3450 watts (peak)
100-175 PSI (6.9-12.0 bar)
4 CFM (113 Liters/Minute)
+32°F to +122°F (0°C to +50°C)
Up to 95% Non-condensing
Up to 10,000 ft. (3048 m)
Cleaning the Console
To maintain a brand new appearance of the display, clean with
soft cloth regularly.
Please remove stubborn stains with soft cleaner rather than strong cleaners
such as diluting agent, benzene or corrosive cleaner as they may damage the
display.
ArmorAll wipes are a suitable cleaning product for the touch screen.
Do not touch the screen with chemicals or solvents on fingers,
i.e. brake cleaner. Doing so will damage the anti-glare protector
on the screen.
End User License Agreement End User License Agreement
Use of equipment and it's operating software is acknowledgment of
agreement to the terms of the End User Licensing Agreement ("EULA"). The
entire EULA can be found by scanning the QR Code below.
Warranty and Environmental Information Warranty and Environmental
Warranty Information
Hunter Engineering Company warrants new equipment to be free from defects
in material and workmanship under normal conditions of use for a period of
three (3) years from the date of installation. Exceptions to this warranty are
listed below:
• Field labor is covered under this warranty for a period of six (6) months.
• ADASLinkTM units carry a one (1) year warranty and remain under
warranty as long as a subscription is maintained there after.
• DAS 3000 units, including electronic circuit boards, carry a one (1) year
warranty.
• Printers carry a one (1) year warranty.
• Normal consumables and wear items are not covered. Exception is
batteries, which are warranted for a period of six (6) months.
• Product that has been subject to abuse, misuse, alterations, accident,
exposure to the elements, tampering, unreasonable use, or not
maintained in a reasonable or necessary manner.
• Replacement parts purchased through the Hunter Service Center and
no longer covered by machine warranty are warranted for a period of six
(6) months.
In case of any warranty claim, it will be necessary to contact your local
authorized Hunter Service Representative. To have an item considered for
warranty, it must be returned to Hunter Engineering Company for inspection
and evaluation. This must be done on a freight prepaid basis. If after our
inspection the product proves to be defective, and is within the time frame
specified, we will repair or replace the item at no additional cost.
This is Hunter Engineering Company's only warranty with respect to new
equipment. Hunter Engineering Company disclaims all other warranties to the
extent permitted by law. This express warranty and any implied warranties of
merchantability and fitness for a particular purpose shall not extend beyond
the warranty period. Hunter Engineering Company is not responsible for any
incidental or consequential damages, including, but not limited to, loss of
business.
We do not authorize any person to assume for us any other liabilities with
our products. Any remaining warranty may be transferred to subsequent
purchasers by forwarding the purchaser's name, address, phone number and
equipment serial number to:
See our document library at www.Hunter.com for additional details.
Environmental Information
The following disposal procedure shall be exclusively applied to the machines
having the crossed-out bin symbol on their data plate.
This product may contain substances that can be hazardous to the
environment and to human health if it is not disposed of properly.
The following information is therefore provided to prevent the release of these
substances and to improve the use of natural resources.
Electrical and electronic equipment should never be disposed of in the usual
municipal waste but must be separately collected for their proper treatment.
The crossed-out bin symbol, placed on the product and on this page, reminds
the user that the product must be disposed of properly at the end of its life.
Information
Figure 4.