Publicidad
Idiomas disponibles
Idiomas disponibles
English
Wall Mounting
Some PORTER-CABLE chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. A)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Proper Hand Position (Fig. A, E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
4
.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
of the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side
of the tool.
8
6
into the tool handle, align
and firmly pull the battery
5
2
determines the direction
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of the tool.
The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.
Variable Speed Trigger Switch (Fig. A)
1. To turn the tool on, squeeze the trigger switch
2. To turn the tool off, release the trigger switch.
3. Your tool is equipped with a brake. The anvil will stop
when the trigger switch is fully released.
4. The variable speed switch enables you to select the best
speed for a particular application. The more you squeeze
the trigger, the faster the tool will operate.
nOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Speed Selector (Fig. A)
Your tool is equipped with a speed selector
you to select one of three speeds. Select the speed based on
the application and control the speed of the tool using the
variable speed trigger switch
SPEED 1
SPEED 2
SPEED 3
Your impact tool can generate the following maximum
torque values (Speed 1, Speed 2, Speed 3).
nOTE: Output torque is dependent on the speed selected,
with the highest provided in Speed 3.
TOOl
sPEED
SPEED 1
PCCF940
SPEED 2
SPEED 3
Worklight (Fig. A)
The worklight
7
is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Anvil (Fig. A)
WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessory prior to use to ensure that
it contains no cracks.
CAUTION: Inspect anvils, and hog rings prior to
use. Missing or damaged items should be replaced
before use.
1
.
which allows
9
.
1
0–450 rpm
0–1200 rpm
0–2000 rpm
Output Torque
100 Ft. Lbs. / 130 Nm
300 Ft. Lbs. / 400 Nm
700 Ft. Lbs. / 950 Nm
Publicidad
