GRAPHITE 58G000 Traducción Del Manual Original página 11

• Drill cannot be started, when the switch is in this position.
• Use this position of the switch to change drills or bits.
• Before starting the tool make sure the position of the direction
selector switch (5) is correct.
Do not change direction of rotation when the drill spindle is
rotating.
CHANGE OF GEAR
Gear switch (4) (fig. H) allows to increase the range of rotational speed.
Gear I: small speed range, big torque
Gear II: greater speed range, small torque.
Set the gear switch in position appropriate for the works to perform.
When the switch is blocked and cannot be moved, turn the spindle
slightly.
Never change the gear switch position when the drill is operating. It
may damage the power tool.
Long lasting drilling at low rotational speed of the spindle may
cause motor overheating. Long lasting drilling at low rotational
speed of the spindle may cause motor overheating.
HOLDER
The drill provides convenient holder (6) that allows to e.g. hang the tool
on a tool belt when working at heights.
OPERATION AND MAINTENANCE
Remove the battery from the device before commencing any
activities related to installation, adjustment, repair or maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with compressed air
at low pressure.
• Do not use any cleaning agents or solvents, they may damage plastic
parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• In case of excessive commutator sparking, have the technical condition
of carbon brushes of the motor checked by a qualified person.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
QUICK RELEASE CHUCK REPLACEMENT
Quick-release chuck is screwed onto spindle of the drill and additionally
secured with a screw.
• Set the direction selector switch (5) in the middle position.
• Open jaws of quick release chuck (1) and unscrew the fixing screw
(left-hand thread) (fig. H).
• Install hexagonal key in the quick release chuck and tap the other end
of the key.
• Unscrew the quick release chuck.
• Installation of the quick release chuck is similar to deinstallation, only
the sequence of actions is reversed.
All defects should be repaired by service workshop authorized by the
manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless drill
Parameter
Battery voltage
Range of idle rotational speed
Range of quick release chuck
Torque control range
Max. torque (soft drive)
Max. torque (hard drive)
Protection class
Weight
Year of production
Graphite Energy+ System Battery
Value
18 V DC
gear I 0-350 min
-1
gear II 0-1250 min
-1
0,8-10 mm
1 – 19 +
drilling
28 Nm
44 Nm
III
1,05 kg
2021
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information
Parameters of produced noise level, such as sound pressure level
Lp and sound power level Lw
A
specified below in this manual, in compliance with EN 60745.
Vibration values a and measurement uncertainty K are determined in
h
accordance with EN 60745-2-1 and specified below.
Vibration level specified below in this manual was measured in
accordance with measurement procedure defined in EN 60745 and
can be used to compare power tools. It can also be used for initial
assessment of exposure to vibrations.
Specified vibration level is representative for main applications of the
power tool. Vibration level may change if the power tool is used for
other purposes, with different working tools or will not be maintained
properly. The abovementioned factors may lead to higher exposure to
vibrations during whole working time.
To precisely define exposure to vibrations, include periods when the
power tool is switched off and when it is switched on but not used for
working. This way total exposure to vibrations may be significantly lower.
Use additional safety measures to protect the user against results of
exposure to vibrations, such as: power tool and working tool maintenance,
proper hand temperature conditions, good work organisation.
Sound pressure level: Lp
Sound power level: Lw = 95 dB (A) K=3dB (A)
A
Vibration acceleration: a
ENVIRONMENTAL PROTECTION
Electrical equipment must not be disposed off with household
waste and, instead, should be utilized at appropriate facilities.
Information on utilization can be provided by the product vendor
or the local authorities. Waste electrical and electronic equipment
contains substances that are not neutral to the natural environment.
Equipment that is not recycled constitutes a potential hazard to the
environment and to human health.
Do not dispose the batteries with household wastes, do not throw
in fire or water. Damaged or worn out batteries should be properly
recycled in accordance with applicable directive for battery
disposal.. Batteries should be returned to collection points fully
discharged, if the batteries are not completely discharged, they
must be protected against short circuits. Used batteries can be
returned free of charge at commercial locations. The buyer of the
goods is obliged to return the used batteries.
Li-Ion
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with seat in Warsaw at
ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all copyrights to this instruction (hereinafter
Instruction), including, but not limited to, text, photographies, schemes, drawings and layout of the
instruction, belong to Grupa Topex exclusively and are protected by laws accordingly to Copyright and
Related Rights Act of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U. 2006 No
90 item 631 with later ammendments). Copying, processing, publishing, modifications for commercial
purposes of the entire Instruction or its parts without written permission of Grupa Topex are strictly
forbidden and may cause civil and legal liability.
11
Value
58G001 58G004
18 V DC 18 V DC
Li-Ion
2000 mAh 4000 mAh
4 C – 40 C 4 C – 40
0 0 0
1 h
0,400 kg 0,650 kg
2021
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 C – 40
0
1 h
2 h
II
0,300 kg
2021
with measurement uncertainty K are
A
= 84 dB (A) K=3dB (A)
A
= 1,552 m/s K = 1,5 m/s
2 2
h
Li-Ion
C
0
2 h
2021
C
0