Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Depth settings are on a sliding scale (4). The left side indicat-
ing the deepest and the right side indicating the shallowest.
To drive a nail deeper, rotate the depth adjustment wheel
u
(3) downwards. This will slide the depth adjustment indica-
tor (4) to the left on the scale.
To drive a nail shallower, rotate the depth adjustment
u
wheel (3) upwards. This will slide the depth adjustment
indicator (4) to the right on the scale.
Loading and unloading the tool (Fig. I, J)
Warning! Keep the tool pointed away from yourself and oth-
ers. Serious personal injury may result.
!
Warning
Never load nails with the contact trip or trigger
activated.
!
Warning
Always remove battery pack before loading or
unloading nails.
!
Warning
The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Loading the tool
Press pusher latch (10) and pull magazine down.
u
Insert fasteners into the side of the magazine. Ensure the
u
fastener tips are placed towards the front of the magazine,
under the nail guide (16) in the nail channel.
Push magazine closed until it locks into place.
u
!
Warning
Keep fingers clear of pusher to prevent injury.
Unloading the tool
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Press the nail pusher latch and pull the magazine down.
u
Tip the tool up until the nails slide freely out of the
u
magazine
Open the jam clear door (7) on the nosepiece to verify
u
there are no nails remaining.
Work lights (Fig. K)
There are work lights (5) located on each side of the nailer.
Work lights turn on upon depressing the contact trip.
Note: These work lights are for illuminating the immediate
work surface and are not intended to be used as flashlights.
Low Battery Indicator:
The left-side worklight will flash four consecutive times and
then shut down to indicate low battery..
12
(Original instructions)
Jammed Nail Indicator:
The right-side worklight will flash continually if a nail becomes
jammed in the nosepiece (see Clearing a jammed nail).
Stall Release (Fig. J)
Warning! If a stall occurs, the tool will disable itself and will re-
quire you to reset it. To do so, follow instructions on clearing a
stalled condition. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
If the nailer is used in a rigorous application where all
available energy in the motor is used to drive a fastener, the
tool may stall. The driver blade did not complete the drive
cycle and the jam/stall indicator will flash.
Rotate the stall release lever (6) on the tool and the mecha-
nism will release as shown in figure L.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position after
rotating the stall release lever, proceed to "clearing a jammed
nail".
Clearing a Jammed Nail (Fig. K)
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
Remove battery pack from tool and engage trigger lock-
u
off.
Remove any loaded nails. Refer to Loading and Unloading
u
the Tool.
Lift the jam clearing latch 7 then pull up to open front door
u
17 .
Remove bent nail, using pliers if necessary.
u
If driver blade is in the down position, cycle stall release
u
lever 6 using enough force to fully slide it to the other end
of the slot in housings.
Close the front door and engage the latch pin under the
u
two arms 18 on the nosepiece. Push latch until it locks in
place.
Reinsert battery pack.
u
Warning!If a jam occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
the jammed nail. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
Publicidad
