Connections; Rear Panel - Pioneer DJM-2000NXS Manual De Instrucciones

Connections

Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Refer to the operating instructions for the component to be connected.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.

Rear panel

1 2
PHONO
OFF POWER
ON
AC IN
l
1 POWER button (page 12)
Turns this unit's power on and off.
2 PHONO terminals (page 7)
Connect to a phono level (MM cartridge) output device. Do not input
line level signals.
3 CD terminals (page 7)
Connect to a DJ player or a line level output component.
4 SIGNAL GND terminal (page 7)
Connects an analog player's ground wire here. This helps reduce
noise when the analog player is connected.
5 CD, DIGITAL (page 12)
Selects the analog signal input terminals (CD) or the digital signal
input terminals (DIGITAL IN).
6 LINE terminals (page 7)
Connect to a cassette deck or a line level output component.
7 CONTROL (page 7)
Connect using a control cord (included with Pioneer DJ players).
8 DIGITAL OUT terminal (page 7)
Outputs the master channel audio signals.
9 DIGITAL IN terminal (page 7)
Connect these to the digital coaxial output terminals on DJ players,
etc. The sound may be momentarily interrupted when the output
signal sampling frequency is switched.
a Kensington security slot
b USB (page 8)
Connect to a computer.
c MIDI OUT terminal (page 7)
Connects this to the MIDI IN terminal on an external MIDI
sequencer.
d LINK terminal (page 7)
Connect these to the LINK terminals on Pioneer DJ players or the
LAN ports of computers on which rekordbox is installed (PRO DJ
LINK).
When connecting a LAN cable, be sure to use an STP
(shielded) cable.
6
En
3 4 5 6 3 7 5
CH4 CH3
CD SIGNAL GND LINE CD
L L
CONTROL
CD DIGITAL CD DIGITAL
R R
MASTER1 MASTER2 REC OUT
R L L
MASTER
ATT.
-6dB -3dB 0dB
R
1GND 2HOT
3COLD
k j i h
8 9
DIGITAL
OUT IN
CH4 CH3 CH2 CH1
BOOTH SEND RETURN
TRS
R L R L(MONO) R
g f e
e RETURN terminals (page 7)
Connect to the output terminal of an external effector. When the [L
(MONO)] channel only is connected, the [L (MONO)] channel input
is simultaneously input to the [R] channel.
f SEND terminals (page 7)
Connect to the input terminal of an external effector. When the [L
(MONO)] channel only is connected, a monaural audio signal is
output.
g BOOTH terminals (page 7)
Output terminals for a booth monitor, compatible with balanced or
unbalanced output for a TRS connector.
h REC OUT terminals (page 7)
These are output terminals for recording.
i MASTER2 terminals (page 7)
Connect to a power amplifier, etc.
j MASTER ATT.
Sets the attenuation level of the sound output from the [MASTER1]
and [MASTER2] terminals.
k MASTER1 terminals (page 7)
Connect to a power amplifier, etc.
Be sure to use these as balanced outputs. Be careful not to acci-
dentally insert the power cord of another unit.
l AC IN
Connects to a power outlet using the included power cord. Wait until
all connections between the equipment are completed before con-
necting the power cord.
Be sure to use the included power cord.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If
accidentally swallowed, contact a doctor immediately.
6 3 7 5 2
CH2 CH1
LINE CD PHONO CD
L L
CONTROL
CD DIGITAL
R
R
CH 3 CH 1 COMPUTER 1
L(MONO)
LINK
CH 4 CH 2 COMPUTER 2
d
3 4 5 a
SIGNAL GND
CD DIGITAL
MIDI OUT USB
c b