Inglesina APTICA Manual De Instrucciones página 35

ADJUSTING THE HANDLEBAR
The chassis features a telescopic handlebar, which can be
adjusted to 4 different positions.
fig. 15 Operate both buttons (T5) and simultaneously
raise or lower the handlebar to the desired position.
STORAGE BASKET
The chassis is equipped with a large storage basket (K), which
can be easily removed if necessary.
fig. 16 To remove the basket, undo the 4 snap fasteners
(K1) that secure it to the side tubes and detach the Velcro flap
(K2) from the rear tube (T6).
fig. 17 Detach the 3 lower snap fasteners and pull the rear
flap (K3) off the central brake unit.
fig. 18 Detach both footplate hooks (K4) from their
respective pins (T7).
fig. 19 With the aid of a screwdriver or similar tool (not
included), expand the front seats (K5) and at the same time
pull off the latch straps (K6) on both sides.
To reinstall the basket, carry out the above operations in
reverse.
FEEDING BOTTLE HOLDER
The chassis is equipped with a standard feeding bottle
holder (H).
fig. 20 To fasten the feeding bottle holder, place the upper
guide in correspondence of the hook (H1) on the chassis and
push it in its housing until it is fully attached.
ADDITIONAL CARRYING UNITS FOR CHASSIS: CARRYCOT,
STROLLER SEAT AND CAR SEAT (if present)
fig. 21 The chassis can be used with the Aptica carrycot,
the All Season stroller seat and the Cab 0+ / Darwin Infant /
Darwin Infant Recline car seat, if present.
APTICA CARRYCOT
ATTACHING THE CARRYCOT TO THE CHASSIS
fig. 22 Take the carrycot from the handle and attach it to
the chassis in correspondence of the housings on both sides
of the structure and place it solely facing the parents.
fig. 23 Once the carrycot is installed, check that the
indicators (C1) on both the attachment devices are Green.
If they are Red, reposition the carrycot correctly until the
indicators turn Green.
fig. 24 Caution: before use, make sure that the carrycot
is properly attached on both sides by pulling it upwards.
DETACHING THE CARRYCOT FROM THE CHASSIS
fig. 25 Operate the lever (C2) located outside the carrycot
and simultaneously lift it, gripping it by the handle.
FITTING THE HOOD LINING
fig. 26 Wrap the hood lining (C) around the handle, fixing
it with the dedicated buttons (C3) and with the central Velcro
fastening strap (C4).
fig. 27 Complete the fitting by attaching the side and rear
Velcro fastenings (C5) to the carrycot.
HANDLE AND HOOD ADJUSTMENT
fig. 28 To adjust both the handle and the carrycot hood,
press the two internal buttons simultaneously (C6).
fig. 29 Caution: Before carrying or lifting the carrycot,
always check that the handle is in its vertical position and
properly locked on both sides.
ATTACHING THE APRON
fig. 30 To fit the apron (D) on the carrycot, first fix the press
studs (D2) and then the two slot buttons (D3).
fig. 31 The front flap of the apron (D1) can be extended
and fixed in a position that protects your child from the cold.
fig. 32 To facilitate access to the child, the apron can be
partially folded, detaching only the two side press studs (D2).
The apron stays fixed to the carrycot through the two slot
buttons (D3).
BACKREST ADJUSTMENT
fig. 33 Operate the lever (C6) to adjust the backrest: once
the desired position is reached, set the lever to the starting
position.
CARRYCOT VENTILATION
The Aptica carrycot features a coordinated
ventilation system.
fig. 34 The ventilation of the base can be
adjusted using the lever (C7) at the front.
fig. 35 If present: The two mesh inserts on the
back and on the hood permit greater circulation
of air inside the carrycot.
MATTRESS AND INTERNAL LINING MAINTENANCE
It is advisable to remove the mattress and internal lining
periodically for correct maintenance.
fig. 36 To remove the internal lining simply release it from
the edge of the carrycot.
CARRYCOT LINING MAINTENANCE
fig. 37 If it is necessary to remove the carrycot cover,
simply pull it off by unfastening the perimeter straps from
the seats on the structure.
fig. 38 When refitting it, ensure that the two elastic loops
(C8) are fitted perfectly underneath the lower tabs (C9) on
both attachment devices.
Caution! Incorrect positioning of the elastic loops could
interfere with correct attachment of the carrycot to the
chassis.
ALL SEASON STROLLER SEAT
ATTACHING THE STROLLER SEAT TO THE CHASSIS
fig. 39 Attach the stroller seat (E) to the chassis,
positioning it in the dedicated housings on both sides of the
structure.
ADJUSTING THE BACKREST
fig. 40 The backrest can be adjusted to 4 positions; use
the central device (E1) and bring the backrest to the desired
position.
fig. 41 Caution: before use, make sure that the stroller
seat is properly attached on both sides by pulling it
upwards.
DETACHING THE STROLLER SEAT FROM THE CHASSIS
fig. 42 Operate the lever (E2) and simultaneously lift the
stroller seat from the chassis.
Caution: do not, under any circumstance, carry out this
operation with the baby inside.
fig. 43 The stroller seat can be used both facing the parent
and facing the street.
ADJUSTING THE FOOTREST
fig. 44 To lower the footrest, use both levers (E3)
positioned on the lower part and simultaneously press them
downwards.
fig. 45 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
SAFETY BELTS
fig. 46 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one.
Position both back straps always at the same height.
35