Publicidad
Idiomas disponibles
Idiomas disponibles
A- Press M key
(menu)
B- Press recall on
remote control
tv set / analyzer
Stored CH
Monitor CH E21
FIG. E2 - IDENTIFICATION OF RF OUTPUT CHANNEL
E2 - Menu Selection:
To select a menu, press successively the "M" key if you
use the frontal buttons (figure E3A) or press the IN, VI-
DEO, AUDIO, OUT, TEST, R4 (SETUP) buttons or succesi-
vely the IN key if you use the programmer (figure E3B)
or press the MENU, red (VIDEO), green (AUDIO), yellow
(OUTPUT), blue (SETUP), INFO (TEST) and pause (CI) if
you use the IR remote control (figure E3C). See the des-
cription of menus starting from E5 step
SETUP
IN
VIDEO
AUDIO
AUDIO
VIDEO
OUT
TEST
SETUP
CI
A
B
FIG. E3
E3 - Selection of the parameters to be
adjusted:
To navigate through the different parameters press the
UP, DOWN keys (or the same keys of previous step, for
the Programmer/remote control. To select a certain pa-
rameter press the > /OK key. See the description of the
parameters starting from E5 step.
E4 - Modification of the parameter values:
To modify a value of a certain parameter press the +
/- keys or press the arrow keys or press the numeric keys
depending of the control system you are using (frontal
keys, programmer or remote control). See the description
of values starting from E5 step.
E5a - INPUT MENU PARAMETERS
(OFDM boards)
Input/Menú
Standard
Band
Video
Channel
Audio
Frequency
Output
Bandwith
Mode
Tes/Info
Modulation
Setup
Guard Interval
CI
SFN
Search Programs
FIG. E4
26
-Input channel standard (B/G, I, L, D/K, BB)
-Input channel (press 00 for central frequency)
-Bandwidth (6,7,8 MHz, Auto)
-Transmission mode (2K, 8K, Auto)
-Modulation system (Auto)
-Guard interval (Auto, 1/32, 1/16, 1/8, 1/4)
-SFN algorithm (NO for static reception)
-Search programs: Press OK over this option for retune
without changes.
Note: Is convenient to select AUTO in the maximum num-
ber of fields that you can.
E5b - INPUT MENU PARAMETERS
(QPSK boards)
Tuned to
the monitor
channel (E21)
E38 (* )
FIG. E5
-Board type: INDIVIDUAL (for independent receivers),
MASTER (for receivers with associated CI slaves) and
SLAVE (for slave receivers).
-DiSEqC (OFF / TO / B / C / D) - to use antenna switches
-LNB LO frequency (typ 10600 or 09750).
-Transponder frequency (10700-12750)
-Transmission symbol rate (for example 22000)
-LNB power supply (one receiver for LNB)
-Polarity of the LNB: Quatro/18V(Recommended)
VER/14V, HOR/18V
-22KHz activation (for the high band of an universal
LNB).
-Search programs: Press OK over this option for retune
without changes.
INFO
Note: For Multi-CI system (fig. D9), before going to E6
step, you should enter "SLAVE option" + OK in Board
type, for all the slave boards associated to Master.
OUT
IN
E6 - VIDEO MENU SCREEN MESSAGES:
MENU
-LOCK OK indicating that the tuner has been locked.
CI (
)
II
-WAIT PAT / PLEASE WAIT while the unit scans the
channels
C
-PROGRAMS LIST: By means of numeric or ^ v/OK keys
select the desired program
If the board doesn't find channels, it will appear the mes-
sage: Wait! Trying SR2000/22000, and if neither finds
them, it will appear the message: Not appear Channels
found. In this case, please review the adjustments of IN-
PUT Menu and all the connections.
FIG. E6
Notes: -If the program is coded, its name will appear
among brackets [ ]
- If the board is a master type, you will be able to open
them by means of >< keys (number in green) or to close
them. The open channels, can be received in the Mas-
ter board or in a connected slave by means of a "cable
stream" (see D2 step).
If some coded program can not be opened in the master,
we recommend you to press MENU/Search programs
option or to delete some services with < key. The open
channels will be confirmed at the end of E9 step (pres-
sing OK key).
If you connect CAM for the first time, you should configu-
re it by means of the CI menu (press successively the M
frontal key until arrive to the CI menu (step E12).
Board type
Input/Menú
DiSEqC
Video
LNB Frequency
Audio
Frequency
Output
Symbol Rate
Tes/Info
LNB Power
Setup
Polarization
CI
Tone 22KHz
Search Programs
1 [RTL9]
Input/Menú
2 [AB1]
Video
3 [AB MOTEURS]
Audio
4 [ANIMAUX]
Output
5 [TF1]
Test/Info
6 [XXL]
Setup
7 [CHASSE & PECHE]
8 [ESCALES]
CI
< > Descramble ch ON/OFF
E7 - AUDIO MENU SCREEN MESSAGES:
Pid=0080 Mono
Input/Menú
Pid=0204 Stereo
Video
Audio
Output
Test/Info
Setup
CI
FIG. E7
-AUDIO AND MODE LIST: By means of ^ v and OK keys
select the desired language and mode (stereo, mono etc.)
Note: the receiver starts up automatically in STEREO or
MONO mode depending of the modulator type incorpo-
rated in the receiver
E8 - OUTPUT MENU PARAMETERS:
Mode:
Input/Menú
Standard:
Video
Band:
Audio
New channel:
Output
Current channel: S03
Test/Info
Audio SC:
5,5MHz
Setup
Volume:
Subtitles:
CI
Letter box:
FIG. E8
-Video standard (PAL/SECAM).
-RF standard (B/G,I,L/D/K,BB).
-RF band (E or S),
-New Output channel (E5,E69, S03/S41) – when
pressing OK key (next step)
-Current Output channel – before pressing OK key
-Audio subcarrier (4,5-5,5-6-6,5)
-Sound level
-Subtitles (if exists).
-Letterbox mode (OFF / ON). To see 16/9 programs
in 4/3 tvsets
Notes: -For standalone modulators the OUTPUT menu is
the first menu appeared on the screen.
-In case the user doesn't know the output channel, it can
be very laborious to find it in the tvset. Consequently we
recommend to always use the AV input of tvset or if it
is not possible (for example in standalone modulators,
please follow the procedure indicated in E1 step).
E9 - PRESS THE "OK" KEY
(to finish and save adjustments)
The message STORED and READY will appear and the
menu will disappear from tv-set (indicating that changes
have been saved).
Notes:
- Press «ESC» to exit without saving the changes.
- If the user left any open menu (without pressing OK or
ESC key) during 4 minutes, the board will save automati-
cally the changes and it will make an auto-reset.
- If the input signal disappears or the tuning lock is not
correct, the receiver will make an auto-reset every 20seg
(Prog. control will show «WaitXM»).
- If you want to re-start yourself the unit please press
the reset key (fig. C4/C5) or disconnect for a while the
general power supply (230Vac).
E10 - TEST/INFO MENU PARAMETERS
-Signal characteristics
-Type of board
-Soft version
Television
Input/Menú
AGC:
STR
Video
TPSignal: Descra
Constell
Audio
Hier:
Mode
Output
FEC:
G.I.
Tes/Info
BER:
SNR
Setup
CI
Freq offset 4KHz
FIG. E9
PAL
B/G
S
S03
63
OFF
OFF
Television
Input/Menú
GAIN
Video
Audio
BER:
Output
Tes/Info
Publicidad
