Publicidad
Idiomas disponibles
Idiomas disponibles
Television
STR
Input/Menú
GAIN:
Video
Audio
BER:
Mode
Output
G.I.
Tes/Info
SNR
Setup
CI
FIG. E10
E11 - SETUP MENU PARAMETERS
Send software
Input/Menú
Watchdog Level
Video
Factory default
Audio
Output
Test/Info
Setup
CI
FIG. E11
A - Send software (NO, SW, SW+CH).
SW option sends software to another board and SW+CH
option sends saved software and channels to another
board. Press Ok and follow the instructions on the screen,
interconnecting units through RS232 null modem cable
(AV0758E). Disconnect and feed the destination unit and
press OK at the end to re-initialize the unit.
Television
Connect a Null Modem cable
between the units. Disconnect
power on the other unit and
reconnect power. Transmission
will start automatically.
Transmitted 0%
FIG. E12
Note: If a software update program is available in your
PC, connect the receiver to the serial port (with RS232
null modem cable). Send the update file using the Hyper-
terminal program included in Windows. After sending
the order, connect the receiver to power supply. Press
OK at the end tp initialize the board
B - Watchdog level (MAX / MIN)
With WatchdogMAX the receiver is more sensitive to the
lost of signal (recommended option, except when the
receiver makes often resets, due to the signal characte-
ristics).
C - Factory default (ALL, PARTIAL).
The ALL option restores everything and PARTIAL restores
all but the output channel, watchdog level and board
type.
E12 - CI MENU
After inserting a CAM, it will appear:
-CAM initializing (please wait)
-CAM initialized OK
- Type of CAM (Viaccess, Conax, Irdeto...)
Note: The following configuration menus will depend on
each CAM.
Input/Menú
Smart card management
System information
Video
Language setting
Audio
Output
Test/Info
Setup
CI
FIG. E13
F - LINK SYSTEM PROGRAMATION
(FAST GuIDE):
F1 - Introduction
The following information describes the configuration
process of the LINK system, which includes 3 different
control modes:
HOTEL-LINK: All modules are controlled from one single
point (typically from the TV outlet located on the Hotel
reception). By default all menus are available, except the
Headend-Installation one, where the installer selects the
parameters of the input signal (to avoid improper modifi
NO
cations from the Hotel reception). Additionally the installer
MIN
will be able to block any other menu (parental control).
NO
In this mode, there will be as many channels available as
modules are in the headend, but from the hotel reception,
at any time, will be possible to modify the channel simply
accessing to a Favourite list of channels.
HOTEL-USER: Every user controls independently its own
module from the hotel room of the hotel. In this mode,
there will be only available the general list of channels,
the language Favourite list and the games. All channels
available in the antenna will be available in the room,
through one single RF channel.
USER-LINK: Every user controls independently its own
module from his apartment. By default all menus are
available, except the Headend-Installation one. All chan-
nels available in the antenna will be available in the
apartment, through one single RF channel.
F2- LINK System Configuration
F2.1 - Every receiver (QPSK or OFDM) includes two le-
vels of software preprogrammed in its memory.
-SMATV: The simplest, robust and most standard soft-
ware. The setup is performed on the headend, which will
offer as many channels as modules. To change a channel
confi guration, the installer must access to the headend.
-LINK: Remote control of the headend, with 3 modes al-
ready described on the previous paragraph. To use this
mode, is necessary to have a MULTILINK (MS1699) ac-
cessory on the TV outlet where we want to control the
headend.
Note: All modules are supplied as factory default in
SMATV mode. The DC8 allows mixing at the same time,
modules in SMATV together with modules in LINK mode.
Atention: Only the boards with 6 or more characters in
their SW label, incorporate the LINK system. If you want
to upgrade software please go to E11A step.
F2.2 - To setup the LINK mode, please refer to the fo-
llowing steps to be performed in the headend. Firstly,
install and connect the DigiCompact8 as described on
the general manual (steps C & D). Connect the video
output of the module (RCA connector) to the TV set or
level meter.
OK
V A
FIG. F1
As indicated on the figure, keep pressed the OK key and
press momentarily the Reset pushbutton (located on the
rear-top part of the module). Hold the OK button for few
seconds until appears on the TV the new window indi-
cated on the figure F1. Repeat the process if it doesn't
appear any information on the screen.
Note - Output channel identification:
If you want to see the menus using the RF output, please
read the E1 step.
Remote control Television
LINK
Select initial FIRMWARE
RESET
SMATV
LINK - MS86XX - X.XX
*SMATV - X.XX
TV
*Active firmware
Press OK to select.
Press ESC to abort.
F2.3 - Select the LINK option and press OK to confi
rm (with the remote control or directly on the module
key). Next, the TV will display the new green menus of
HEADEND INSTALLATION (See figure F2).
F2.4 - If the HEADEND INSTALLATION does not appear
automatically press the M (Menu) key on the module.
The red led will fast-blink (programmation mode) and
the green Menu will be displayed.
FIG. F2
F2.5 - In this mode, the installer can setup all the RF
output signal parameters, and the remote control mode
(see paragraph F1).
F2.6 - Press OK to confirm the programmation. After
the WAIT message, the installation menu will appear
(figure G1).
F2.7 - In this menu, the installer can select language
(SYSTEM CONFIGURATION/LANGUAGE).
FIG. F3
In the user installation menu you will be able to setup all
the typical features of a receiver, especially the satellite
antenna/LNB setup (fig. G2 and G3).
F2.8 - Press autosearch channels option (figure G4, G5
and G6). Before starting the search function; the system
will ask if you want to automatically create the lists of Fa-
vourite channels (by language). If so, press OK, select the
desired languages (up to maximum 8) and press again
OK. The system will search all channels available, and
will create different list based on the selected languages.
When the process is done, please validate the lists by
pressing OK.
F2.9 - After the autosearch process is done, press M
and OK again. When entering into the channel organi-
zing menu, you can edit, modify or delete channels. You
can move through the different language lists, by pres-
sing the FAV key on the remote control.
Please note, that the automatic classification of langua-
ge lists, is done based on the information sent by the
broadcaster. If the broadcaster sends the code "UNDE-
FINED", this channel will not be assigned to any list, but
you can then edit the channel and added to a specific list
by pressing the key LANG.
FIG. F4
27
Publicidad
