Publicidad
Idiomas disponibles
Idiomas disponibles
F2.10 - To exit from the Installation menu, press the
Exit key. Press OK in case you want to save the chan-
ges. The first channel on the list, will appear on the TV
set. You should repeat the steps F2.2 to F2.10 for every
receiver board you want to setup in LINK mode. Plea-
se note that every module must have a different output
channel. It's useful to write the RF output channel in a
label over each receiver board. The tv set must be tuned
to the all RF output channels corresponding to all recei-
vers. It's also useful to note the input program tuned in
every receiver.
F2.11 - Connect the MULTILINK directly to the output
of the amplifier (MS8641/31) to test the product (see the
figure F5 for the connection of Multilink). Connect the
Test output of the amplifier to the TV set / level meter.
Tune the TV to the output channel of the module (see
figure F2 or step E1) and verify the picture is correct.
MS8641/31
MULTILINK
Receiver
Receiver
FIG. F5
Note: To work with the Multilink, it's essential to have the
MS8641/31 amplifier installed on the DigiCompact8, as
well as the 2 cables connected to the power supply (see
figure F5. You also should interconnect all boards with
corresponding bridges (see sections C & D) and adjust
levels as it is explained in the step H of this manual.
F2.12 - Place the deep-switch of the Multilink on the
proper position based on the following table:
HOTEL uSER /
REMOTE MODE
HOTEL LINK
uSER LINK
(Headend Installation
menu)
Refer to figure F7 & F8.
OFF/ON//ON//
MULTILINK switches
Every RF output channel has
ON//ON//ON//
(from 8 to 1)
ON//ON
one corresponding switch
ON = Down
combination. (i. e: ch 21 all
OFF = Up
switches to OFF)
FIG. F6
28
Channels
Todos sist.
BGIt
S3
S4
S5
S6
S7
S8
S9
S10
E5
D
E6
E
E7
F
E8
G
E9
H
E10
H1
E11
H2
E12
TO TV-SET
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
FIG. F7 - USER LINK / HOTEL USER CODE FOR VHF
OUTPUT CHANNELS
Switches ON
BB
1
2
3
4
5
6
7
8
2
7
2
7
8
2
6
2
6
8
2
6
7
2
6
7
8
2
5
2
5
8
2
5
7
5A
2
5
7
8
6
2
5
6
7
2
5
6
8
8
2
5
6
7
8 Syd
2
5
6
7
8
9
2
4
9A
2
4
8
10
2
3
4
8
10N
2
3
4
7
11
2
3
4
7
8
11N
2
3
4
6
12
2
3
4
6
8
2
4
7
2
4
7
8
2
4
6
2
4
6
8
2
4
6
7
2
4
6
7
8
2
4
5
2
4
5
8
2
4
5
7
2
4
5
7
8
2
4
5
6
2
4
5
6
8
2
5
6
7
2
5
6
7
8
2
3
2
3
8
2
3
7
2
3
7
8
2
3
6
2
3
6
8
2
3
6
7
2
3
6
7
8
2
3
5
2
3
5
8
2
3
5
7
2
3
5
7
8
2
3
5
6
2
3
5
6
8
2
3
5
6
7
2
3
5
6
7
8
2
3
4
Channels
Switches ON
Todos sist.
BB
1
2
3
20
3
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
E40
E41
E42
E43
E44
E45
E46
E47
E48
E49
E50
E51
E52
E53
3
E54
3
E55
3
E56
3
E57
3
E58
3
E59
3
E60
3
E61
3
E62
3
E63
3
E64
3
E65
3
E66
3
E67
3
E68
3
E69
3
70
3
71
3
72
3
73
3
74
3
75
3
FIG. F8 - USER LINK / HOTEL USER CODE FOR UHF
OUTPUT CHANNELS
F2.13 - Select on your TV the program you would like to
modify. Press, either Menu or OK, on the remote control
focussing toward the infrared sensor of the Multilink. If
the remote mode is HOTEL LINK, a small window will
appear on the corner of the TV set, with the Pin code
(4 digits).
F2.14 - Press these 4 digits on the remote control to
access into the programmation menus (in the modes
Hotel-user and User-Link, you will access directly to the
menus without Pin code). The menus available (dark
blue), depending on the remote mode are:
4
5
6
7
8
4
8
8
7
7
8
6
6
8
6
7
6
7
8
5
5
8
5
7
5
7
8
5
6
5
6
8
5
6
7
5
6
7
8
4
4
8
4
7
4
7
8
4
6
4
6
8
4
6
7
4
6
7
8
4
5
4
5
8
4
5
7
4
5
7
8
4
5
6
4
5
6
8
4
5
6
7
4
5
6
7
8
8
7
7
8
6
6
8
6
7
6
7
8
5
5
8
5
7
5
7
8
5
6
5
6
8
5
6
7
5
6
7
8
4
4
7
4
7
8
4
6
4
6
8
4
6
7
4
6
7
8
Publicidad
