Ryobi RY72ZTRX76 Manual Del Usuario página 7

■
The side discharge chute is a guard that covers the
side discharge opening on the cutting deck and deflects
grass clippings and debris away from the operator.
Always ensure that the motor is off and the blades have
stopped moving before inspecting, moving, cleaning, or
performing maintenance on the side discharge chute.
■
Replace damaged blades and bolts in sets to preserve
balance.
■
Remove the start key from the product before storing,
servicing, or changing accessories. Such preventive
safety measures reduce the risk of starting the product
accidentally.
■
You may make adjustments and repairs described in this
manual. For other repairs, have the product serviced by
an authorised service centre only.
■
Contact an authorised service centre to replace
damaged or unreadable labels.
■
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition.
■
The blade bolts must be tightened to the recommended
torque.
■
Check the brakes before each use and frequently during
use. Adjust and service the brakes as required.
■
Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the product.
■
The cutting blades continue to rotate for a few seconds
after the motor is turned off. When servicing the blades,
be aware that even though the power source is switched
off, the blades can still be moved. Never place any part
of the body in the blade area until you are sure the
blades have stopped rotating.
■
The blade on the product is sharp. Use extreme caution
and wear heavy-duty gloves when fitting, replacing,
cleaning or checking bolt security.
■
After each use, clean the plastic parts with a soft, dry
cloth. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
■
Keep the product free of grass, leaves, or other debris
build up.
■
Do not use water to clean the product. Use an air moving
device, such as a compressor or leaf blower to clean
the product.
TYRE MAINTENANCE
The product is equipped with tubeless tyres. When tyres are
worn, the traction of the mower decreases, which increases
the chance of having an accident. Replace the tyres when
the depth on the tread is 4 mm or less, or any time there is
damage to the tyre. Always use original replacement tyres.
Using incorrect tyres on the product could cause loss of
control, which could cause serious personal injury.
Have the tyres replaced only by an authorised service centre.
TYRE AIR PRESSURE
Check the air pressure in all four tyres before each use.
Improper air pressure aff ects handling, steering response,
traction, tyre life, level cutting, and operator comfort. Make
sure that tyres are infl ated to the recommended air pressure.
The tyre air pressure should only be measured or adjusted
when tyres are cold.
TYRE REPAIR
If a leak or fl at tyre occurs due to a puncture, the tyre may be
repaired using a plug-type patch. If the damage is from a cut, or
if the puncture cannot be repaired using a plug, replace the tyre.
BRAKE ADJUSTMENT
See page 162.
Ensure that the brakes are properly functioning before each
use and frequently during use. Improper brake function can
cause loss of control in an emergency situation and result in
death or serious personal injury.
If the mower travels further before stopping when stepping
on the brake pedal, the brakes need adjusting.
After fi nal adjustment, test the brakes by driving the mower
at normal speed on fl at ground to be sure that the mower
stops quickly when brake pedal is stepped on.
CLEARING BLOCKAGES
■
Turn off the product, engage the parking brake,
and remove the start key. Set the cutting deck to the
maximum height. Make sure that all moving parts have
come to a complete stop.
■
Always wear heavy-duty gloves when checking or
clearing a blockage. The blades are sharp and the
blockage itself could be a sharp object.
■
Check and carefully clear the side discharge chute for
blockages. Remember that the blade may move during
cleaning.
KNOW YOUR PRODUCT
See pages 144-145.
1. Grass catcher boost button
The grass catcher boost button works with the grass
catcher accessory. This button will engage a fan to help
push grass clippings through the catcher tube.
2. Blade engage knob
The blade engage knob activates or stops the cutting
blades.
● Pull up the blade engage knob to activate the blades.
● Press the blade engage knob to stop the blades.
NOTE: The blades should stop within 5 seconds. If the
blades do not stop, contact an authorised service centre.
3. Power switch with start key
The power switch turns the product on and off. The start
key must be inserted before the switch can be operated.
When the key is in the ON position, the power switch
is also used to power optional manufacturer-approved
mower accessories.
4. USB port
The USB charging port provides charging power of 5
V dc at up to 2 A for your cell phone, MP3 player, or
other USB devices. Check the manual of your device for
specific charging requirements.
Connect one end of a USB cable (not provided) to your
device and the other end to the USB charging port on the
product to charge your device.
NOTE: The USB port is powered only when the start key
is in the ON position.
WARNING! Attempting to charge devices rated more
than 2 A could damage the USB charging port and the
mower. Always close the USB cover when not in use to
prevent trapping debris in the port.
7
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO