Publicidad
Idiomas disponibles
Idiomas disponibles
nOTE: Do not rest fingers on platen during use. Move it in
long sweeping strokes across the surface, letting it do the
work. Light pressure is all that is required for sanding.
Helpful Hints
•
Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
•
Do not start sanding without having the sandpaper
attached to sanding platen.
•
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for the
finishing surfaces. If necessary, first make a test run on
scrap material.
•
Excessive force will reduce the working efficiency and
cause motor overload. Replacing the accessory regularly
will maintain optimum working efficiency.
•
Do not allow the sandpaper to wear away, it will damage
the sanding pad.
•
If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for
2–3 minutes to cool the motor. Avoid prolonged usage
at very low speeds. Always keep the blade sharp.
LED Worklight (Fig. A)
The LED worklight
7
will activate when the variable speed
switch
1
is depressed, and will automatically turn off
20 seconds after the variable speed switch is released. If the
variable speed switch remains depressed, the worklight will
remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by PORTER‑CABLE, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
PORTER‑CABLE recommended accessories should be
used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact PORTER-CABLE. Call 1‑888‑848‑5175 or visit our
website: www.portercable.com.
Belt Hook (Fig. J)
Optional Accessory, Sold Separately
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMPORTAnT: When attaching or replacing the belt hook,
use only the screw
12
that is provided. Be sure to securely
tighten the screw.
The belt hook
can be attached to either side of the tool
11
using only the screw provided, to accommodate left- or
right-handed users. If the hook is not desired at all, it can be
removed from the tool.
1. To move belt hook
11
belt hook in place then reassemble on the opposite side.
2. Be sure to securely tighten the screw
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERVICE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFIRMATIOn OF OWnERshIP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.portercable.com.
, remove the screw that holds the
.
12
EnglIsh
11
Publicidad
