BH HIPOWER R250 Instrucciones De Montaje Y Utilización página 10

Ocultar thumbs Ver también para R250:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 39
ASSEMBLY INSTRUCTIONS.-
1.
Take the unit out of its box and make sure that
all of the pieces are there, Fig.1:
(F01) Handrail.
(H)
Monitor.
(A01) Main body.
(F02) Handrail Handlebar.
(J01)
Rear trim cover.
(J02)
The adapter.
(K06) Screw M-10x30.
(K07) Screw M-10x80.
(K08) Allen screw M-6x65.
(K09) Allen screw M-8x25.
(K10) Allen screw M-8x55.
(K11) Allen screw M-10x25. 4
(K12) Screw Phillips M-5x15.
(K13) Screw Phillips M-4x15.
(K14) Flat washer M-10.
(K15) Flat washer M-8.
(K16) Grower washer M-8.
(K17) Grower washer M-10.
(K01) Combination spanner.
(K02) Star driver spanner.
(K03) Allen key 5mm.
(K04) Allen key 6mm.
(K05) Allen key 8mm.
2
. FITTING THE HANDRAIL
HANDLEBAR.-
Bring the handrail handlebar (F02) up to boss on
the main body (A01), Fig.2
Take terminal (A16) and, with the help of the cord
(20-22) already inserted inside the handlebar tube,
pull it in through the tube (F02) bringing it out
trough the top.
Now slip the handlebar tube over the boss on the
main body (A01) in the direction of the arrow, as
shown in Fig.2, making sure not to snag any of the
cables.
Next, take screw (K11) along with the spring
washer (K17), Fig.2, and secure. Then take screws
(K07) along with their spring weashers (K17) and
flat washers (K14) and secure. Finally, take screws
(K06) along with the spring washers (K17) and flat
washers (K14) and tighten securely, including
those fitted previously.
3.
FITTING THE
Release screws (K18), Fig.3, at the back of the
monitor.
Bring the monitor (H) to the handlebar stem (F01)
Fig.3, connect the terminal (A16) coming out of the
handlebar stem (F01) and the monitor (H16), Fig.3.
Take hold of the Hand-grip connector (H17),
sticking out of the main post 31, and plug it into
(H17), located at the back of the monitor (H), as
shown in Fig.3.
MONITOR.-
Take hold of the handrail monitor (F01) and bring it
up to the handlebar tube, as shown in Fig.4.
Connect the terminals (A16), sticking up out of the
top of the tube, with terminal (H16) coming down
from the bottom of the monitor (F01), Fig.4, and
insert the tube on the monitor into the boss on the
main body (A01) in the direction of the arrow,
making sure not to snag any of the cables.
Check that the cables are connected correctly by
spinning the dynamo until the monitor starts to
operate.
Once you have checked that it works, insert
screws (K08) and (K10) along with their flat
washers (K15), Fig.4.
Then take screws (K09), along with the spring
washers (K16), and tighten as shown in Fig.4A.
Line the handlebar up with the machine and
tighten the screws securely.
4.
FITTING THE FRONT TRIM COVER.-
Place the trim cover (J01) on the front part of the
machine, Fig.4. Next, take screws (K12) and
secure the cover by tightening the screws.
5.
FITTING THE TOP TRIM COVERS.-
Move the top trim covers up to the handlebar tube,
Fig.4. Take screws (K13) and screw them on.
6.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise Fig.5, make sure that it sits flat
on the floor and that it is level. This can be
achieved by screwing the adjustable support
blocks (R) up or down, as shown in Fig.6.
7.
MOVEMENT & STORAGE.-
The appliance is equipped with wheels (E06)
making it easier to move about. The two wheels at
the front of the appliance make it easy to store the
machine away, as shown in Fig.7.
8.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (H02) located on the seat
handgrips or the handlebar, see Fig.8.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (H02) located
on the seat handgrips or handlebar.
10
SK
LINE
LINE
LINE
LINE
sportkoncept

Publicidad

Tabla de contenido
loading

Tabla de contenido