Publicidad
Idiomas disponibles
Idiomas disponibles
Technical data
4.5
Scope of delivery
The scope of delivery is described in the shipping document and the content is
shown on the packaging.
Immediately after receipt of the goods, please check the shipment for
completeness and damage. Please notify us immediately of any transport
damage.
Basic pressure-maintaining equipment:
•
One primary vessel up to 600 litres and one compact control unit.
•
"LIS" pressure load cell for level sensing.
4.6
Optional equipment and accessories
•
Secondary vessels with connection sets for the primary vessel.
•
For make-up with water
–
Make-up without pump:
•
Solenoid "Fillvalve" with ball valve and Reflex Fillset for make-
up with drinking water.
–
Make-up with pump:
•
Reflex Fillcontrol Auto, with integrated pump and a system
separation vessel or Auto Compact
•
For make-up and degassing with water:
–
Reflex Servitec S
–
Reflex Servitec 35- 95
•
Fillset for make-up with drinking water.
–
With integrated system separator, water meter, dirt trap and locking
mechanisms for the "WC" make-up line.
•
Fillset Impulse with FQIRA+ contact water meter for make-up with
drinking water.
•
Fillsoft for softening or desalination of the make-up water from the
drinking water network.
–
Fillsoft is installed between Fillset and the device. The device
controller evaluates the make-up quantities and signals the required
replacement of the softening cartridges.
•
Optional expansions for Reflex controllers:
–
I/O module for standard communication.
–
Master-Slave-Connect for master controllers for maximum 10
devices.
–
Bus modules:
•
Profibus DP
•
Ethernet
•
Diaphragm rupture monitor
Note!
Separate operating instructions are supplied with accessories.
5
Technical data
5.1
Control unit
Permissible ambient temperature
Degree of protection
Noise level
Electric output
Power supply
Fusing
Electrical voltage control unit
Number of RS-485 interfaces
Weight
Permissible operating temperature
Permissible flow temperature
I/O module
22 — English
5.2
6
0 – 45 °C
IP 54
72 dB
750 W
230 V / 50 Hz
3 A
230 V / 2 A
1
21 kg
70 °C
120 °C
optional
Reflexomat Basic — 13.11.2020 - Rev. A
Tanks
Primary vessel
Note!
The following values apply for all vessels:
–
Operating pressure:
–
Connection:
Type
Diameter Ø
Weight
"D" (mm)
(kg)
200
634
37
300
634
54
400
740
65
500
740
78
600
740
94
Installation
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•
Ensure that the system is voltage-free before installing the device.
•
Ensure that the system is secured and cannot be reactivated by other
persons.
•
Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there
is a risk of burns and other injuries at the connection points, if pressurised
hot water or hot steam suddenly escapes.
•
Ensure proper installation, removal or maintenance work.
•
Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•
Wear protective gloves.
•
Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to falls or bumps
Bruising from falls or bumps on system components during installation.
•
Wear personal protective equipment (helmet, protective clothing,
gloves, safety boots).
WARNING
Risk of injury due to heavy weight
The devices are heavy. Consequently, there is a risk of physical injury and
accidents.
•
Use suitable lifting equipment for transportation and installation.
Secondary vessel
6 bar
R1"
Height "H"
Height "h"
Height "h1"
(mm)
(mm)
(mm)
970
115
155
1270
115
155
1255
100
140
1475
100
140
1720
100
140
Publicidad
