Technical Specifications Of Product - Nice HOPP HO7124 Instrucciones Y Advertencias Para La Instalación Y El Uso

WARNINGS: • All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to apply modifi-
cations to products at any time when deemed necessary, maintaining the same intended use and functionality.
Type
Maximum torque
Rated torque
Speed under no load
Speed at rated torque
Maximum cycle frequency *
Maximum time of continuous
cycle **
Application limits
Lifetime
Power supply
Back-up power supply
Solar power
Maximum power absorption
at rated torque
Peak power
Rated current absorption
Maximum current absorption
Absorbed power with
"All – Standby" function when
powered by PS124 or SYKCE
kit (including OXI receiver)
Flashing light output ***
Electric lock output ***
BLUEBUS output
STOP input
SS input
OPEN input
Radio engage
Radio AERIAL input
Programmable functions
Self-learning
Functions
Assembly
Operating temperature
Use in acid, saline
or potentially explosive
atmospheres
IP protection rating
Dimensions (mm)
Weight (kg)
[*]
Cycle frequency at maximum temperature: 25 cycles/hour
**]
[ Maximum continuous cycle time at maximum temperature: 8 minutes
[***]
The outputs Flashing Light and Electric lock can be programmed with other functions (see "TABLE 5 – Level 1 functions"; or via the Oview programmer; see chapter
trical specifications of the output are adapted to the type of selected function: • flashing light function: lamp 12 V
outputs (all types): 1 lamp or relay 24V
12 – English
www.metalines.com

TECHNICAL SPECIFICATIONS OF PRODUCT

HO7124
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release. Built-in control unit and OXI radio receiver.
the product can be used on gates with leaf weight up to 250 kg for lengths up to 1,5 m and weight up to 160 kg
estimated between 80.000 cycles and 250.000 cycles, depending on the conditions reported in Table 15 and Graph 3
230 V (120 V for version HO7124/V1)
±10%; 50/60 Hz
provision for buffer battery PS124
provision for SYKCE kit
170 W
280 W
0,8 A (1,6 A for version HO7124/V1)
1,3 A (2,6 A for version HO7124/V1)
less than 100 mW
one LUCYB flashing light (12 V
one electric lock, 12 V
one output with load of maximum 15 Bluebus units
(max. 6 pairs of MOFB or MOFOB photocells plus 2 pairs
of MOFB or MOFOB photocells routed as opening devices
plus max. 4 MOMB or MOTB control devices)
for normally closed contacts, normally open contacts
or contacts with constant 8,2 kΩ resistance; selection
of the type of contact is in self-learning mode and
a modification with respect to the memorised status
will generate a "STOP" command
for normally open contacts (closure of the contact
generates a Step Step command)
for normally open contacts (closure of the
contact generates a Partial Open 1 command)
SM connector for receivers in the families SMXI,
OXI and OXIFM
50 Ω for cable type RG58 or similar
8 ON-OFF type functions (Table 5) and 8 settable
functions (Table 6)
• Self-learning of devices connected to the BlueBus output
• Self-learning of the type of device connected
to the "STOP" terminal (NO, NC contact or 8,2 kΩ)
• Self-learning of the gate leaf travel
and automatic calculation of deceleration
points and partial opening. • Self-learning of operation
with one or two motors
from -20°C to +50°C (at low temperatures, gearmotor efficiency is reduced)
9
(-30 to +50%), max. 4 W.
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release.
250 Nm
100 Nm
0,17 rad/s (1,6 rpm)
0,13 rad/s (1,2 rpm)
35 cycles/hour
10 minutes
for lengths up to 2,4 m
, 21 W)
max 15 VA
Vertical, with dedicated fixing plate
NO
IP 54 (with container intact)
180 x 252 x 290 h
, 21 W max; • electric lock function: 12 V
HO7224
24 V (±25%)
50 W
100 W
2 A
4 A (for maximum time of 1 s)
6,5
15 VA max; • other
sales@metalines.com
8.3
). The elec-