Publicidad
Idiomas disponibles
Idiomas disponibles
ence a hypersensitive (e.g. severe reddening, blistering, itchiness,
heavy sweating) or allergic skin reaction to the heat radiation.
If symptoms are not relieved after 6 to 8 applications, stop using
the device and consult your doctor.
7. USAGE
7.1 Starting treatment
WARNING
Always use the supplied protective
eyewear during treatment. Monitor the
area of the body being irradiated and the
reaction of the skin regularly. Should signs
of hypersensitivity or allergic reactions
occur, cease radiation immediately and
consult a doctor.
Risk of burns! During treatment, never touch the hot
glass pane
.
2
1. Hold the protective eyewear to your eyes and pull the rubber
band over your head. You can adjust the rubber band indi-
vidually.
2. Press the ON/OFF switch
vice switches on automatically after a short time. The remaining
time display
shows 15 minutes as the duration of treatment.
4
3. Use the time selection button
ment duration (1 to 15 minutes). The set treatment duration
is displayed in the remaining time display
change the duration of treatment after it has started using the
time selection button
3
4. After the set treatment duration has elapsed, the device switch-
es off automatically. To stop the treatment early, press the ON/
OFF switch
.
5
7.2 After treatment
NOTICE
• The fan will continue running for 5 minutes after you have
finished using the device in order to cool it down. Please
do not unplug the device during this period.
• Once the cooling period has finished, the fan will switch itself
off. Pull the mains plug out of the socket.
• If the device is warm, do not cover it or pack and store it.
8. CLEANING AND MAINTENANCE
8.1 Cleaning
WARNING
The device must be switched off, disconnected from the mains,
and allowed to cool down fully each time before each cleaning.
NOTICE
• Make sure that no water gets inside the device!
• Do not clean the device in the dishwasher.
The device may be cleaned with a damp cloth. Do not use any
solvent-based cleaning products. The device should be cleaned
after each use.
Clean the protective eyewear from time to time. Use a slightly
damp, soft cloth to clean it. Do not use any harsh or abrasive
cleaning products.
to switch on the device. The de-
5
3
to select the desired treat-
. You can also
4
.
8.2 Replacing the infrared lamp
Please note that only an infrared lamp of the same type may be
used as a replacement for a defective infrared lamp.
WARNING
Risk of electric shock!
• Unplug the mains cable from the socket before replacing the
infrared lamp!
• Risk of burns from hot surfaces.
• Allow the device to cool fully before starting repair work.
• Infrared light sources are excluded from the guarantee.
Removing the old infrared lamp
1. Place the cooled device with the ceramic glass pane on a flat
surface.
2. Unscrew the four screws on the rear panel of the device using
a suitable Phillips screwdriver (see Figure
3. Set the housing upright. However, allow the front part with the
ceramic glass pane to rest on a raised surface, e.g. a book
(see Figure
).
B
4. Hold the cooled infrared lamp at its right end and carefully
press it to the left
C
5. Now pull the right end of the infrared lamp forwards out of
the socket.
Inserting the new infrared lamp
NOTICE
Only insert the new infrared lamp using a cloth. Do not touch the
infrared lamp with bare fingers, as the layer of grease adhering to
your skin may damage it.
1. Insert the new infrared lamp into the socket using a cloth. In-
stallation of the new infrared lamp is carried out in the reverse
sequence to removal.
2. Close the device again. Closing of the device is carried out in
the reverse sequence to the opening.
3. Ensure that no objects remain in the housing and no cables
are trapped.
If you have problems replacing the infrared lamp, please contact
Customer Services.
Storage
1. Remove the mains plug and allow the device to cool fully be-
fore moving it.
2. If you do not plan to use the protective eyewear for an ex-
tended period of time, we recommend storing it in its original
packaging in a dry environment, ensuring that it is not weighed
down by other items.
3. The heat lamp should ideally be stored in the original packag-
ing and in a dry place.
9. WEAR PARTS AND REPLACEMENT
PARTS
To purchase wear parts and replacement parts, please visit www.
beurer.com or contact the corresponding service address (ac-
cording to the service address list) in your country.
Designation
Replacement lamp
Type: Halogen light source
220 – 230 V / 300 W
118 mm length for R7S socket
16
).
A
.
Item number and/or order
number
110.048
Publicidad
