Function Selection - Mitsubishi Electric PFAV-P VM-E Serie Manual De Instrucciones

3.4. Function Selection

Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting when needed.
Item 1
1. Change Language Language setting to display
("CHANGE
LANGUAGE")
2. Function limit (1) Operation function limit setting (operation lock) ("LOCKING
("FUNCTION FUNCTION")
SELECTION")
(2) Temperature range limit setting ("LIMIT TEMP FUNCTION")
3. Mode selection (1) Remote controller main/sub setting ("CONTROLLER MAIN/
("MODE SUB")
SELECTION")
(2) Use of clock setting ("CLOCK")
(3) Timer function setting ("WEEKLY TIMER")
(4) Contact number setting for error situation ("CALL.")
4. Display change (1) Temperature display °C/°F setting ("TEMP MODE °C/°F")
("DISP MODE
(2) Suction air temperature display setting ("ROOM TEMP DISP
SETTING")
SELECT")
[Function selection flowchart]
[1] Stop the air conditioner to start remote controller function selection mode. → [2] Select from item 1. → [3] Select from item 2. → [4] Make the setting. (Details are
specified in item 3) → [5] Setting completed. → [6] Change the display to the normal one. (End)
Normal display (Display when
the air condition is not running)
(Hold down the E button and press the D button for two
seconds.)
* The display cannot be changed during the unit function
selection, the test run and the self diagnosis.
Item 1
Press the G button.
Change Language
("CHANGE LANGUAGE")
Press the
E button.
Function limit
("FUNCTION
Press the
SELECTION")
G button.
Press the Press the
E button. E button.
Press the
G button.
Mode selection
("MODE
SELECTION")
Press the
E button.
Press the
Display change G button.
("DISP MODE
SETTING")
12
Item 2
Remote Controller Function
Selection Mode
Item 2
Operation function limit setting ("LOCKING FUNCTION")
Use of automatic mode setting ("SELECT AUTO MODE")
Temperature range limit setting ("LIMIT TEMP FUNCTION")
Use of automatic filter elevation panel up/down operation mode setting
[ ]
Use of fixed airflow direction mode setting
[ ]
Remote controller main/sub setting ("CONTROLLER MAIN/SUB")
Use of clock setting ("CLOCK")
Timer function setting ("WEEKLY TIMER")
Contact number setting for error situation ("CALL.")
Temperature display °C/°F setting ("TEMP MODE °C/°F")
Suction air temperature display setting ("ROOM TEMP DISP SELECT")
Automatic cooling/heating display setting ("AUTO MODE DISP C/H")
• Display in multiple languages is possible
• Setting the range of operation limit (operation lock)
• Setting the temperature adjustable range (maximum, minimum)
• Selecting main or sub remote controller
* When two remote controllers are connected to one group, one
controller must be set to sub.
• Setting the use or non-use of clock function
• Setting the timer type
• Contact number display in case of error
• Setting the telephone number
• Setting the temperature unit (°C or °F) to display
• Setting the use or non-use of the display of indoor (suction) air
temperature
(Hold down the E button and press
the D button for two seconds.)
* The remote controller records the
setting that is made in this way.
See [4]–1.
(Setting content)
See [4]–2. (1)
Press the
Press the G button.
D button.
See [4]–2. (2)
See [4]–2. (3)
See [4]–2. (4)
See [4]–2. (5)
Press the
D button.
See [4]–3. (1)
Press the G button.
See [4]–3. (2)
See [4]–3. (3)
See [4]–3. (4)
Press the
D button.
See [4]–4. (1)
Press the G button.
See [4]–4. (2)
See [4]–4. (3)
Item 3 (Setting content)
NOTE
Timer operation stops when the
display for remote controller
function selection is changed to
the normal one.
Dot display
The language that is selected
Item 3
in CHANGE LANGUAGE
mode appears on this display.
English is set in this manual.
F
TEMP.
MENU ON/OFF
E
BACK MONITOR/SET DAY
CLOCK
PAR-21MAA
G
C
ON/OFF
I
A
FILTER
CHECK TEST
B
OPERATION
CLEAR
H
D