Korg KingKORG NEO Manual Del Usuario página 12

KingKORG NEO Owner's Manual
Making connections and turning on the power
Connections
The illustration below shows a typical example of connections for the KingKORG NEO. Connect your equipment as appropriate for your needs.
Cable hook
Rear panel
AC adaptor
(included)
to electrical
outlet
You must power-off all your equipment before making connections. If you make connections while the power is on, you might damage
your speaker system or cause your equipment to malfunction or be damaged.
1 .
Connecting your monitor amp or
speakers
Connect the KingKORG NEO's AUDIO OUTPUT jacks to the input
jacks of your mixer or powered monitor speakers. If you make
connections in monaural, use the L/MONO jack.
TIP: We recommend that you use the stereo outputs to take full
advantage of the KingKORG NEO's sound.
2 .
Connecting
your mic
To use the KingKORG NEO as a
vocoder, connect the included
vocoder mic to the front panel mic
jack, so that the audio from the mic
input can be used as the
modulator. (OM: p.15 "Playing
vocoder sounds")
Align the mic plug with the pin
positions on the jack, and insert
the mic's plug until you hear a
click.
12
MIDI keyboard, sound module,
rhythm machine, etc.
L/MONO R 1 2 3 4 IN OUT IN OUT TO HOST TO DEVICE DC 9V
AUDIO OUT AUDIO IN SYNC MIDI
BD SD LT HT CH OH RS CP SP 1 SP 2 MULTI
BASS DRUM SNARE DRUM TOMS HIGH HATS SAMPLE 1/2 drumlogue VOLUME
HYBRID DRUM MACHINE
TEMPO
DECAY DECAY LT DECAY CH DECAY SP 1 ATTACK
HT DECAY SP 2 ATTACK
PAGE
TUNE TUNE LT TUNE OH DECAY SP 1 DECAY
HT TUNE SP 2 DECAY
CLAP
MUTE
PROGRAM KIT
DRIVE SNAPPY LT DETUNE DECAY SP 1 TUNE
SELECT SAVE SELECT SAVE PART
HT DETUNE SP 2 TUNE
QUEUE QUEUE
YES NO PATTERN EDIT
< >
TIME LIVE CHAIN LOOP STEP ACCENT MOTION SHIFT
GROOVE 32 16 8 TRIP. SHRINK EXPAND GLOBAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ANALOG DIGITAL MULTI EFFECTS
BD SD LT HT CH OH RS CP SP 1 SP 2 VPM NOISE USER DELAY REVERB MASTER
AUDIO IN CHOKE RAND.PART CLEAR PART CLEAR ALL ON/OFF CLEAR STEP CLEAR PART CLEAR ALL SYNC POLY COPY PART RAND.PART CLEAR PART CLEAR ALL INIT
KIT MOTION PATTERN
MIDI IN MIDI OUT
MIDI cable
Foot controller
Windscreen
(included)
Vocoder mic
(included)
Computer
USB cable
Pedal switch Damper pedal
3 .
Connecting pedals and switches
Connect a foot controller and pedal switch as desired.
ASSIGNABLE SW jack
Here you can connect an optional pedal switch (PS-1/PS-3), foot
controller (EXP-2), or expression/volume pedal (XVP-20).
Before you use these, you must adjust the settings in Global mode to
specify the type of device (switch or pedal) that you've connected.
With the factory settings, this jack is set to use a switch-type device,
and is assigned to the "program up" (Prog. Up) function.
Different functions are available for switches and pedals.
If you've specified a switch (Switch), you'll be able to change
programs, switch the octave, or turn portamento on/off. Normally
the function will remain on only while you continue holding down
the pedal, but if desired, you can change this so that the function
will toggle on/off each time you press the pedal. If you've specified a
pedal (Pedal), you'll be able to control parameters such as volume,
expression, and pan. (PG: "8. Foot parameters")
DAMPER jack
Here you can connect an optional DS-1H damper pedal or PS-1
pedal switch, allowing you to turn the damper effect on/off.
Monitor speakers
(with internal amp)
Input Input